GovChime
Notice ID: 90d372b98ca8482bb247818bbdd578f2Combined Synopsis/SolicitationArchived

Mini Injector Molder

Archived on May 24, 2025. Original response deadline: . Full description on SAM.gov.

Overview

Response deadline
3:00 PM CDT
Posted
May 7, 2025
Notice type
Combined Synopsis/Solicitation
NAICS
334516: Analytical Laboratory Instrument Manufacturing
Agency
Department of AgricultureAGRICULTURAL RESEARCH SERVICE

Notice details

Office
USDA ARS AFM APD
Place of performance
Peoria, IL, 61604
Last updated
Nov 14, 2026
First published
Last updated on SAM.gov

Identifiers

Solicitation number
12505B25Q0084
Notice ID
90d372b98ca8482bb247818bbdd578f2

Description

***Full and Open Competition, this is NOT a small business set aside.*** This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in Subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; quotes are being requested and a written solicitation will not be issued. Solicitation number 12505B25Q0084 is issued as a request for quote (RFQ). The solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 2025-03 dated January 17, 2025. The associated NAICS code is 334516 (Analytical Laboratory Instrument Manufacturing). This acquisition is for the following item as identified in the Line Items: (ThermoFischer Scientifics HAAKE Mini-Jet Pro brand name or equal) Benchtop size: 50x50x100cm (LxWxH) or less Capable of small-scale operation (5 grams or less) Processing section temperature range: ambient to 400 C (or higher) Mold temperature range: ambient to 250 C (or higher) Maximum injection pressure: 1000 bar or higher Dogbone mold: Mold for ASTM D638 Type V Tensile bar included DMA bar mold: Mold for rectangular DMA bar (80x10x4mm) included Water chilled cooling system for molds Integrated control unit for injection molder parameters and settings Installation, testing, and calibration of the equipment Training on use of the equipment One year warranty The Contractor shall provide all items F.O.B. destination. Location of the Government site is USDA, in Peoria, IL. and will also be identified in the contract. The Government anticipates award of a Firm Fixed Price contract. See attached Clauses and Provisions document for the Federal Acquisition Regulation (FAR) and the Department of Agriculture Acquisition Regulation (AGAR) provisions and clauses that apply to this acquisition. Offerors responding to this announcement shall submit their quote in accordance with FAR 52.212-1 Instructions to Offerors Commercial Products and Commercial Services and include a copy of 52.212-3 Offeror Representations-Commercial Products and Commercial Services. Submission of quote shall include the following: (1) Technical and (2) Price. All responses shall be submitted electronically to brian.brusky@usda.gov The basis for award is Lowest Price Technically Acceptable (LPTA). LPTA means the best value is expected to result from selection of the technically acceptable quote with the lowest evaluated price. Pursuant to FAR 52.212-2 Evaluation Commercial Products and Commercial Services, the criteria for evaluation are: (1) Technical and (2) Price and must also have neutral or better past performance. The lowest priced quote will first be evaluated for technical acceptability in accordance with the minimum specifications identified. If determined not technically acceptable, it will be removed from competition and the next lowest priced quote will be evaluated for technical acceptability. This will continue until the lowest price quote is determined technically acceptable. Once the lowest priced quote is determined technically acceptable, then a determination of responsibility will be completed. If found responsible, evaluations will be closed, and award will be made. INSPECTON AND ACCEPTANCE TERMS: Services will be inspected by Contracting Officer Representative (COR) and accepted at destination. Period of Performance - 30 Days ARO. To be eligible for an award, all contractors must be registered in the System for Award Management (SAM) at the time the quote is submitted. A contractor can contact SAM by calling 1-866-606-8220 or www.sam.gov. NO EXCEPTIONS. A SAM UEI number is required in order to register. All invoices shall be submitted electronically. Quotes must be received no later than 3:00 PM Central Time on May 9, 2025. Questions in regard to this combined synopsis/solicitation are due no later than 1:00 PM Central on May 6, 2025. Answers to any questions received by that time will be posted as an amendment to this combined synopsis/solicitation. DISCLAIMER: The official contract documents are located on the government webpage and the Government is not liable for information furnished by any other source. Amendments, if/when issued will be posted to Contract Opportunities for electronic downloading. This will normally be the only method of distributing amendments prior to closing; therefore, it is the offeror's responsibility to check the website periodically for any amendments to this solicitation. Websites are occasionally inaccessible, due to various reasons. The Government is not responsible for any loss of internet connectivity or for an offeror's inability to access the documents posted on the referenced web pages. The Government will not issue paper copies.

Full description on SAM.gov

Award Overview

No prior contract identified

No prior award matched this notice's agency, NAICS, place of performance and PSC within 18 months. It may be a new requirement.

Contacts

Documents

Files (2)

  • Provisions and Clauses Q0084.docx

    80 KBAdded in Combined Synopsis/Solicitation version 2Posted
    Download
  • Specifications Injector Molder.pdf

    144 KBAdded in Combined Synopsis/Solicitation version 1Posted
    Download

Lifecycle

  1. 1
    Version 1Combined Synopsis/SolicitationArchived

    Mini Injector Molder

    Notice c8ed8b9b1cd843e0b79b893271212d9a on SAM.gov

  2. 2
    Version 2Combined Synopsis/SolicitationArchived

    Mini Injector Molder

    Notice 09c888ef2cba47728c017db230f70fbf on SAM.gov

  3. 3
    Version 3Combined Synopsis/SolicitationCancelledArchived

    Mini Injector Molder

    Notice 43ae9d0d8ea54602ad64149b0f054d85 on SAM.gov

  4. 4
    Version 4Combined Synopsis/SolicitationArchived

    Mini Injector Molder

    Notice 62311321bf98498ea771debf5f99fbe3 on SAM.gov

  5. 5
    Version 5Combined Synopsis/SolicitationArchived

    Mini Injector Molder

    Notice 0e9c63eba6ee482595e843b8b32add07 on SAM.gov

  6. 7
    Version 7Combined Synopsis/SolicitationArchivedCurrent

    Mini Injector Molder

    Notice 90d372b98ca8482bb247818bbdd578f2 on SAM.gov

  7. 10
    Version 10Award NoticeArchived

    Type changed from Combined Synopsis/Solicitation to Award Notice

    Mini Injector Molder

    Notice 2cb1137465b54f6384d2fa0b03023af7 on SAM.gov

Similar Opportunities

Title
Match
Phase
Deadline

Additional Details

Solicitation Number

12505B25Q0084

Archive Date

May 24, 2025

Office Address

BELTSVILLE, MD, 20705