GovChime
Notice ID: be6c8c76180443b2b1936f153f708a5fCombined Synopsis/Solicitation

Custom Grasshopper Cages

Archived on August 25, 2020. Original response deadline: . Full description on SAM.gov.

Overview

Response deadline
4:00 PM UTC−05:00
Posted
July 27, 2020
Notice type
Combined Synopsis/Solicitation
Set-aside
Total Small Business Set-Aside (FAR 19.5)
NAICS
314999: All Other Miscellaneous Textile Product Mills
Agency
Department of AgricultureAGRICULTURAL RESEARCH SERVICE

Notice details

Office
USDA ARS PA AAO ACQ/PER PROP
Place of performance
Sidney, MT, 59270
Last updated
Apr 29, 2026

Identifiers

Solicitation number
12805B20Q0092
Notice ID
be6c8c76180443b2b1936f153f708a5f

Description

The Agricultural Research Services Division of the USDA requests construction of custom grasshopper cages. Sidney Montana, USDA Grasshopper Cages 0.5 m2 cage specifications 110 cages based on per cage price. We can provide a sample cage with pvc frame. We need 2 distinct heights of cages. 50 cages made at 30 tall, 55 cages made at 24 tall. 1. Finished internal dimensions: 55 cages with internal dimensions 24 tall, with all sides 28.5 wide. Top should be 28.5 x28.5 finished internal. 50 cages with internal dimensions 30 tall, side dimensions the same as above. See attached photos. 2. Screening: Lumite insect screening (woven 100% polyethylene 14x18 mesh per inch). As this is a specialized material and specs are critical, screening material will be provided by us and shipped to you in 6 x100 rolls with a cardboard inner tube. 3. Bottom cage flap: A 6 wide flap of 18oz coated vinyl added to the bottom (tan, white, grey or other light color). Cage flap should sit on ground perpendicular to the sides of the cage and have no break at the corners, a continuous flap around the corners. See photo (figure 1). See more information on seams in point 6 below. 4. Grommets: Bottom flaps need 8 grommets (~1 O.D., minimum 0.5 I.D.) consisting of one at each corner and one in the middle of each side located ~1.5 from the inside edge of the vinyl flap. Each grommet should have reinforcing material (extra square of vinyl) to avoid ripping out. Grommets must be spaced 1.5 from the junction of lumite and vinyl (figure 2). Depending on seam location, corner grommets may be okay without extra reinforcing material. 5. Zippers: 2 Opposite sides of the cage will each have an 18 YKK #10 Vislon Delrin Black Zipper (Ex: https://www.sailrite.com/YKK-Continuous-Vislon-Zipper-Chain-Black-10) with single pull. The zipper itself should be approximately 18 in height above the base and ~centered on the wall this will be the same for both cages. Zipper should be sewn into a 3 high piece of vinyl inset into the cage that will reduce stress on the screening when opening and closing. The vinyl inset should extend 1.5 beyond the zipper on the ends, as shown in the photos (figure 3 interior and exterior cage view). 6. Seams: All seams should be double stitched. It is critical that the interior of the cage doesnt have any pockets created by concealed seams as our insects get trapped in these. Frayed and unfinished edges on the interior of the cage are also bad as the insects can impale themselves on the stiff Lumite threads. a. Seams on the vinyl inset for the zippers need to be double-stitched with raw edges of Lumite concealed within the seams as the Lumite tends to unravel (figure 3). b. Vinyl-Lumite seams on bottom flap should also be double-stitched with sufficient Lumite overlap. c. Lumite-Lumite seams need to be flat felled seams, wide enough to prevent seam failure due to lumite fraying (minimum inch finished seam width). If unable to serge the edge of the Lumite, seams need to have raw edges to the exterior of the cage for Lumite-Lumite seams (figure 4). d. To minimize the number of seams on the cage, a continuous piece of Lumite should be used for the top and the 2 sides that dont have zippers if there is an easier way to construct the cage, we are open to changing this particular requirement as long as all seams follow the above specifications. It is essential that seams be a minimum finished flat felled width of inch. 7. To prevent the need for modifications, we will provide a priority next day air shipping label to send a prototype cage to us that we will check the day we receive it. See attached specifications for photos of cages. If interested in submitting a price quote, please fill out the attached SF-1449 Form and email to james.porter@usda.gov before the deadline.

Full description on SAM.gov

Award Overview

No prior contract identified

No prior award matched this notice's agency, NAICS, place of performance and PSC within 18 months. It may be a new requirement.

Contacts

Documents

No documents available.

Lifecycle

Solicitation:12805B20Q0092
  1. Combined Synopsis
  1. Combined SynopsisCurrentJul 27, 2020

    Custom Grasshopper Cages

    Notice be6c8c76180443b2b1936f153f708a5f on SAM.gov

Similar Opportunities

Title
Match
Phase
Deadline

Additional Details

Solicitation Number

12805B20Q0092

Archive Date

Aug 25, 2020

Office Address

FORT COLLINS, CO, 80526