Notice ID: ec98af59d7c14173afc45100876dac0aPresolicitation
NOTICE OF INTENT TO SOLE SOURCE: West Coast Netting, Inc. to provide additional extension to Barrier Netting
Archived on May 16, 2020. Original response deadline: . Full description on SAM.gov.
Overview
- Response deadline
- 3:00 PM UTC−07:00
- Posted
- May 11, 2020
- Notice type
- Presolicitation
- Set-aside
- Total Small Business Set-Aside (FAR 19.5)
- NAICS
- 314994: Rope, Cordage, Twine, Tire Cord, and Tire Fabric Mills
- Agency
- Department of AgricultureAGRICULTURAL RESEARCH SERVICE
Notice details
- Office
- USDA ARS PWA AAO ACQ/PER PROP
- Place of performance
- Salinas, CA, 93905
- Last updated
- Dec 4, 2025
Identifiers
- Solicitation number
- 12905B20R129160
- Notice ID
- ec98af59d7c14173afc45100876dac0a
Description
NOTICE OF INTENT TO SOLE SOURCE: West Coast Netting, Inc. to provide additional extension to Barrier Netting THIS NOTICE OF INTENT IS NOT A REQUEST FOR PROPOSALS. This notice is for informational purposes only and is not to be construed as a commitment by the Government. USDA/ARS/PWS intends to negotiate, on a sole source basis, under authority of FAR 13.106-1(b)(1) with to provide additional extension to Barrier Netting. The Sole Source Determination is based only one responsible source and no other supplies or services will satisfy agency requirements. This notice of intent is not a request for competitive proposals, and no solicitation package is available. However, firms that believe they can fully meet the governments requirements may submit substantiating documentation in writing to the buyer via email lam.pham@usda.gov within 5 days after publication of this synopsis. Such documentation will be evaluated solely for the purpose of determining whether to conduct this procurement on a competitive basis. A determination by the government not to conduct a competitive procurement, based upon responses to this notice, is solely with the discretion of the government. Oral communication is not acceptable in response to this notice.
Award Overview
No prior contract identified
No prior award matched this notice's agency, NAICS, place of performance and PSC within 18 months. It may be a new requirement.
Contacts
Documents
No documents available.
Lifecycle
Solicitation:
12905B20R129160- Pre-Solicitation
Formal solicitation typically follows within 30–60 days. (estimate)
- Pre-SolicitationCurrentMay 11, 2020
NOTICE OF INTENT TO SOLE SOURCE: West Coast Netting, Inc. to provide additional extension to Barrier Netting
Similar Opportunities
Title | Match | Phase | Deadline |
|---|---|---|---|
| - | Awarded | Open | |
This is a combined synopsis/solicitation for commercial products or commercial services prepared in accordance with part 5.101(d). This announcement constitutes the only solicitation. Offers are being requested and a separate written solicitation will not be issued. Solicitation number [insert solicitation number] is issued as a [insert request for quotation (RFQ), request for proposal (RFP), or invitation for bid (IFB)] for [provide a brief description of the requirement]. This acquisition [is/is not] set-aside for small business concerns. This solicitation incorporates provisions and clauses by reference. The full text of provisions and clauses may be accessed electronically at www.acquisition.gov. NOTICE FOR FILING AGENCY PROTESTS United States Department of Agriculture (USDA) Ombudsman Program The United States Department of Agriculture (USDA) is committed to fair, transparent, and efficient acquisitions. Interested parties with concerns about this solicitation are encouraged to seek resolution through the following USDA procedures. Tier 1: Contracting Officer Concern Resolution Submission: Interested parties with concerns about either the solicitation or subsequent award should first submit their concern directly to the Contracting Officer, providing sufficient detail to allow the Contracting Officer to understand and assess the issue. Process: The Contracting Officer will review the concern, seek clarification as needed, and engage with the interested party to attempt prompt resolution. Review Timeline: The Contracting Officer will make every effort to provide a response or resolution within 10 business days of receiving the concern. Effect on Award or Performance: Tier 1 engagement is not considered an official notification of filing an agency protest and does not pause solicitation deadlines, delay award decisions, or suspend contract performance. Next Steps: If the matter cannot be resolved at Tier 1, the interested party may file a written agency protest under Tier 2. USDA encourages all parties to seek resolution with the Contracting Officer before filing an agency protest. Tier 2: Agency Protest If concerns cannot be resolved at Tier 1, an interested party may file a written agency protest with either the Contracting Officer or the USDA Independent Review Authority. The decision by the USDA Independent Review Authority is an alternative to a decision by the Contracting Officer. The USDA Independent Review Authority will not consider an appeal of the Contracting Officer’s decision on an agency protest. The protest must state whether the protester elects review by the Contracting Officer, by the UDSA Independent Review Authority. If no election is stated, the Contracting Officer will decide the protest. Required Information: Protests shall include the information set forth in FAR 33.104-4 (a)(3). Failure to submit the required information may result in a delay or dismissal of the protest. Submission: Agency protests should be submitted electronically to SPE.inquiry@usda.gov and the Contracting Officer. Timeliness: Protests must be filed within the timeframes specified in FAR 33.104. Effect on Award or Performance: Contract awards or performance will be suspended during the protest period unless justified in writing for urgent and compelling reasons or determined to be in the best interest of the Government. Review Timeline: USDA strives to resolve agency-level protests within 35 business days of receipt. Election of Forum: By filing a protest with USDA, the protesters agree not to file a protest on the same matter with the Government Accountability Office (GAO) or any other external forum while the agency protest is pending. If such a protest is filed externally, the USDA agency protest will be dismissed. Questions: Questions regarding this notice or protest procedures should be directed to the Contracting Officer identified in this solicitation. | - | Combined Synopsis | 11/09/2026 |
UPDATE: AMENDMENT 0001 IS HEREBY POSTED, ANSWERING QUESTIONS FROM INDUSTRY, ADDITION OF CONTROLLED PICTURES, AND UPDATING POC INFORMATION. PLEASE SEE ATTACHED FOR MORE INFORMATION. Army Contracting Command - Rock Island issues Solictitation W519TC27RA006 for the purchase of Lifting Pull Strap, in accordance with Drawing 12577572, Rev. K. The solicitation is for a guaranteed minimum of 13,500 ea Lifting Pull Straps on a five (5) Year, Firm Fixed Price, Indefinite Delivery Indefinite Quantity (IDIQ). Solicitation is a Total Small Business Set Aside. Please see the Solicitation and Attachments for further information. | - | Solicitation | 11/23/2026 |
Amendment 0004 The purpose of this amendment is to extend the response time for this opportunity until November 3, 2026 at 1400 EST. Amendment 0003 The purpose of this amendment to is to provide the following response to Industry question: Question 1: Amendment 0002 confirms part number 7155408 and states that 7152800 is obsolete. If the manufacturer’s certificate of conformance, technical data, or test report identifies part 7155408 as “Robtec STS” rather than “Ocean STS,” will that documentation be acceptable provided it clearly identifies part 7155408 and demonstrates compliance with every stated technical requirement? Answer 1: Yes. The documentation will be acceptable provided it clearly identifies part # 7155408. Question 2: Because the required 3,000-meter continuous length must be newly manufactured, may an offeror submit representative manufacturer-certified test documentation and a written manufacturer commitment with its quotation, followed by the actual production-lot certificate of conformance and certified test report with delivery? Or must the quotation include certified results for the specific production lot that will be delivered? Answer 2: The offeror may submit representative manufacturer- certified test documentation and a written manufacturer commitment with its quotation followed by the actual production-lot certificate of conformance and certified test report. Question 3: Must proof-load testing cover the entire continuous 3,000-meter length, or is the manufacturer’s standard lot-based or sample-based proof-load testing acceptable? Please confirm the applicable proof-load or sampling requirement. Answer 3: The Manufacturer’s standard lot-based or sample-based proof-load testing is acceptable. Question 4: For this total small-business set-aside, may an eligible small-business reseller supply the specified Robline product, or must the offered product be manufactured by a qualifying small-business manufacturer? If a class or individual waiver applies, please identify it. Answer 4: Any eligible small-business reseller may supply the specified Robline product for this total small-business set-aside under the SAT. Amendment 0002 The purpose of this amendment is to extend the respose period for this opportunity and to provide the following responses to Industry questions. Question 1: The combined synopsis identifies “Robline (Ocean) STS” 8 mm rope as part 7155408. Robline’s published catalog lists 7152800 for the 8 mm Ocean STS (Dyneema) variant and 7155408 for the 8 mm Robtec STS (HMPE) variant; both show 9,430 daN breaking load and about 47 g/m linear density. Answer 1: The required part number is 7155408. The number listed below (7152800) is an old part number and is now obsolete. Question 2: Please confirm whether the required product is the Robtec STS 7155408 or Ocean STS 7152800, and which product name must appear on the manufacturer CoC and test reports. The notice also specifies elongation no greater than 0.19% at 94.3 kN, which is the stated breaking-strength threshold. Please confirm the intended test load and method for that elongation figure so we can obtain matching certified data. Answer 2: The specified elongation no greater than 0.19% at 94.3 kN corresponds to the ultimate breaking strength. Elongation is measured at the point of failure during a standard "pull to break" (destructive) test. The manufacturer's standard destructive testing method (measuring elongation at the ultimate breaking strength threshold) is fully acceptable to the Government. Amendment 0001 The purpose of this amendment to is to provide the following response to Industry question: Question 1: Please confirm the intended elongation test requirement and test load for Robline P/N 7155408. The solicitation states elongation ≤0.1% at 94.3 kN, while 94.3 kN is the published average breaking-load value. Please advise the acceptable manufacturer test method and documentation required for technical acceptability. Answer 1: As indicated in the RFQ, the elongation requirement is ≤0.19% at 94.3 kN (not ≤0.1% as stated in the question). See basis of award in this RFQ for technical acceptability criteria. This is a combined synopsis/solicitation for commercial products or commercial services prepared in accordance with the format in subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; proposals are being requested and a written solicitation will not be issued. Request for Quotation (RFQ) number is N66604-27-Q-0041. This requirement is being solicited as a 100% small business set-aside. The North American Industry Classification System (NAICS) Code for this acquisition is 314994 Rope, Cordage, Twine, Tire Cord, and Tire Fabric Mills. The Small Business Size Standard is 1,000 Employees. The Naval Undersea Warfare Center Division, Newport (NUWCDIVNPT) requires procurement of the following brand name item, no substitutions permitted. Item Description Part # Qty. Quoted Unit Price (Offeror to Fill In) Quoted Extended Price (Offeror to Fill In) Robline (Ocean) STS 8mm diameter rope 7155408 1 spool/ 3000m $ $ This specific brand of rope is essential due to its unique performance characteristics, including high breaking strength, minimal elongation, and low shrinkage values, which are critical for the extreme ocean environments in which the equipment operates. Utilizing an alternative brand would alter physical tolerances, necessitating a costly and complex system redesign. Furthermore, this specific rope is required for critical engineering and qualification testing of deployment systems, making timely delivery essential to meet scheduled operational requirements. Delivery is F.O.B. Destination: InterOcean Systems, LLC, 9201 Isaac Street, Suite C, Santee, CA 92071 The Government’s required delivery is 16 weeks After Date of Contract (ADC) or sooner. Spool and Packaging The contractor shall: deliver 3,000 meters as a single, continuous, unspliced piece on one spool. No factory splices, mechanical joints, or knots are acceptable. The anchor line shall be wound on sturdy, weather-resistant reel/spool suitable for field deployment and long-term storage. The spool shall prevent tangling, hockling, kinks, and bird-nesting during payout and spooling. Core diameter shall comply with manufacturer bend radius recommendations for 8mm HMPE line. The spool shall be labeled with contract number, manufacturer lot/batch number, date of manufacture, fiber type, length, and nominal diameter. Offerors shall include shipping cost into the unit price in the table above. A separate line for shipping will not be provided. Quality Assurance, Inspection, and Verification: Certificate of Conformance (CoC) The vendor shall provide an official Manufacturer Certificate of Conformance (CoC) with the shipment certifying that: The delivered material is Robline Ocean STS 8mm. The product is newly manufactured (first-run production, not surplus or aged inventory). The lot has undergone factory proof-load testing and visual inspection. Test Data and Factory Acceptance Reports: The contractor shall provide certified test reports verifying Average Breaking Strength (≥94.3 kN), Safe Working Load (≥18.86 kN), elongation (≤0.19% at 94.3 kN), and linear density (47.2 g/m). The Government intends to award a single FFP purchase order to the eligible, responsible offeror whose quote is the lowest price technically acceptable. In order to be determined technically acceptable, the offeror shall: Quote brand name item, no substitutions allowed, in the required quantity; Submit technical data sheets or manufacturer cut-sheets with specs with its quote; and Submit verifiable QA and testing documentation with its quote. In accordance with DFARS 252.204-7024, the Government will consider SPRS risk assessments (including item, price, and supplier risk) during the evaluation of quotations. A high-risk rating or negative performance history in SPRS may demonstrate a high risk of unsuccessful performance and could result in the quote being excluded from consideration for award. In accordance with DFARS Clause 252.211-7003, the contractor shall provide a unique item identifier (UID) for all delivered items for which the Government’s unit acquisition cost is $5,000.00 or more. This solicitation requires registration with the System for Award Management (SAM) prior to award, pursuant to applicable regulations and guidelines. Registration information can be found at www.sam.gov. Offerors shall include price, payment terms, delivery terms, and the following additional information with submissions: Offeror Point of Contact (including phone number and email address); Offeror CAGE Code; and Offeror SAM UEI. The Government’s method of payment will be electronic payment via Wide Area Workflow (WAWF). Incorporated provisions and clauses are those in effect through the latest Federal Acquisition Circular (FAC). Full text of incorporated FAR/DFARS clauses and provisions may be accessed electronically at https://acquisition.gov/far. The following FAR provisions and clauses apply to this solicitation: --FAR 52.203-11, Certification and Disclosure Regarding Payments to Influence Certain Federal Transactions (Sep 2007) --FAR 52.204-13, System for Award Management Maintenance (Oct 2018). --FAR 52.204-19, Incorporation by Reference of Representations and Certifications --FAR 52.204-23 Prohibition on Contracting for Hardware, Software, and Services Developed or Provided by Kaspersky Lab and Other Covered Entities (NOV 2021) --FAR 52.204-24 Representation Regarding Certain Telecommunications And Video Surveillance Services Or Equipment (Nov 2021). -- FAR 52.204-25 Prohibition on Contracting for Certain Telecommunication and Video Surveillance Services or Equipment (Nov 2021) --FAR 52.204-26, Covered Telecommunications Equipment or Services—Representation (Oct 2020) --FAR 52.209-2, Prohibition on Contracting with Inverted Domestic Corporations—Representation (Nov 2015) --FAR 52.209-10 Prohibition on Contracting with Inverted Domestic Corporations (NOV 2015) --FAR 52.209-11, Representation by Corporations Regarding Delinquent Tax Liability or a Felony Conviction under any Federal Law (Feb 2016) --FAR 52.212-1 Instructions to Offerors—Commercial Items --FAR 52.212-2 Evaluation—Commercial Items --FAR 52.212-3 Offeror Representations and Certifications – Commercial Items (DEVIATION 2025-O0003) (DEVIATION 2025-O0004) --FAR 52.212-4 Terms and Conditions—Simplified Acquisitions (Commercial Products and Commercial Services) --FAR 52.232-39, Unenforceability of Unauthorized Obligations (JUN 2013) --FAR 52.232-40, Providing Accelerated Payments to Small Business Subcontractors (NOV 2021) --FAR 52.232-1, Payments (Apr 1984) --FAR 52.233-4, Applicable Law for Breach of Contract Claim (OCT 2004) --FAR 52.252-1, Solicitation Provisions Incorporated by Reference (Feb 1998) In addition, the following Defense Federal Acquisition Regulations Supplement (DFARS) clauses and provisions apply to this order: --DFARS 252.203-7000, Requirements Relating to Compensation of Former DoD Officials (SEP 2011) --DFARS 252.203-7002, Requirement to Inform Employees of Whistleblower Rights (DEC 2022) --DFARS 252.203-7005, Representation Relating to Compensation of Former DoD Officials (Sep 2022) --DFARS 252.204-7008, Compliance with Safeguarding Covered Defense Information Controls (Oct 2016); --DFARS 252.204- 7009, Limitations on the Use or Disclosure of Third-Party Contractor Reported Cyber Incident Information (Oct 2016); --DFARS 252.204-7012, Safeguarding Covered Defense Information and Cyber Incident Reporting (Dec 2019); --DFARS 252.204-7015, Notice of Authorized Disclosure of Information for Litigation Support (May 2016); --DFARS 252.204-7018, Prohibition on the Acquisition of Covered Defense Telecommunications Equipment or Services (Jan 2021); --DFARS 252.211-7003, Item Unique Identification and Valuation (JAN 2023) --DFARS 252.204-7024, Notice to Prospective Suppliers on Use of Supplier Performance Risk System in Past Performance Evaluations Quotes shall be submitted electronically via email to Maria Diaz-Sotomayor at maria.d.diaz-sotomayor.civ@us.navy.mil and Teresa Michael at Teresa.m.michael2.civ@us.navy.mil Quotes and questions regarding this acquisition must be received on or before 03 November 2026 at 1400 Eastern Standard Time (EST). Quotes received after this date are late and may not be considered for award. | - | Combined Synopsis | 11/03/2026 |
Proposed procurement for NSN 4240015435536 LANYARD,SAFETY,INDUSTR: Line 0001 Qty 620 UI EA Deliver To: W1A8 DLA DISTRIBUTION By: 0060 DAYS ADO Approved source is 55297 1246075. The solicitation is an RFQ and will be available at the link provided in this notice. Hard copies of this solicitation are not available. Specifications, plans, or drawings are not available. All responsible sources may submit a quote which, if timely received, shall be considered. Quotes may be submitted electronically. | - | Combined Synopsis | 10/19/2026 |
Additional Details
Solicitation Number
12905B20R129160
Archive Date
May 16, 2020
Office Address
ALBANY, CA, 94710