Notice ID: 189bd6d8c6f04f1591a47c1d97ae858cSolicitation
Crowd Control - R-1, Colombia
Archived on July 18, 2020. Original response deadline: . Full description on SAM.gov.
Overview
- Response deadline
- 12:00 PM UTC−04:00
- Posted
- June 22, 2020
- Notice type
- Solicitation
- Set-aside
- Total Small Business Set-Aside (FAR 19.5)
- NAICS
- 332992: Small Arms Ammunition Manufacturing
- Agency
- Department of State
Notice details
- Office
- ACQUISITIONS - INL
- Last updated
- Dec 4, 2025
Identifiers
- Solicitation number
- 191NLE20Q0068
- Notice ID
- 189bd6d8c6f04f1591a47c1d97ae858c
Description
Crowd Control equipment, see Attachement 1 (SOW)
Award Overview
No prior contract identified
No prior award matched this notice's agency, NAICS, place of performance and PSC within 18 months. It may be a new requirement.
Contacts
Documents
No documents available.
Lifecycle
Solicitation:
191NLE20Q0068- Solicitation
Award typically follows within 30–90 days after the response deadline. (estimate)
- 2×SolicitationCurrentJun 5, 2020
Crowd Control - R-1, Colombia
Similar Opportunities
Title | Match | Phase | Deadline |
|---|---|---|---|
Amendment 1: This amendment hereby extends the due date for receipt of quotations FROM: November 13, 2026 to December 11, 2026 17:00 (Mexico City time). The extension gives the Government time to respond to technical questions from quoters and to coordinate with the U.S. Small Business Administration on the applicability of the Nonmanufacturer Rule (FAR 52.219-33). This is a combined synopsis/solicitation for commercial products or commercial services prepared in accordance with FAR Part 12. This announcement constitutes the only solicitation. Quoters are being requested and a separate written solicitation will not be issued. Solicitation number 19AQMM27Q0008 is issued as a Request for Quotations (RFQ) for an IT solution including workstations, monitors, and geospatial analysis software licenses, along with installation services for the Government of Mexico's Secretariat of the Navy, Naval Intelligence Unit (MARINA-UIN). This acquisition is set aside for small business concerns under NAICS 334111 – Electronic Computer Manufacturing. This solicitation incorporates provisions and clauses by reference. The full text of provisions and clauses may be accessed electronically at www.acquisition.gov. (ii) Line Items: See attached SF-1449, Section A (CLINs 001–009). (iii) Description of Requirements: See attached SF-1449, Section C-001 and Attachment 1 (Statement of Work), including Appendix A – Technical Specifications. (iv) Delivery and Acceptance: F.O.B. Destination at MARINA-UIN, Coyoacán, Mexico City. See attached SF-1449, Section F-006 and SOW for full schedule and delivery address. (v) Applicable Solicitation Provisions: See attached SF-1449 (vi) Applicable Contract Clauses: See attached SF-1449 (vii) Quotation Due Date, Time, Place, and Point of Contact: Quotations are due no later than 5:00 p.m. CST (Mexico City) on December 11, 2026, submitted via email to Alexander Bring (BringAG@state.gov). See attached SF-1449, Section L-001 for full submission instructions. (viii) Additional Information: Quoting firms must maintain an active SAM registration reflecting small business status under NAICS 334111. Award will be based on a comparative evaluation of quotations under FAR 12.203(c)(2). See attached SF-1449. | - | Combined Synopsis | 12/11/2026 |
The International Narcotics and Law Enforcement Section of the Embassy of the United States of America in Serbia supports procurement of a scenario-based laser shooting range system and complementary tactical preparedness and response police training kits to complete new training facilities at University or Criminal Investigation and Police Studies in Belgrade, Serbia. This training solution will provide controlled, analytical training environment needed to assess, document, and translate scenario-based tactical instruction into measurable performance improvements, institutional accountability and long-term learning. SUBSTANTIVE REQUIREMENTS The contractor shall fulfill the following substantive requirements (See Attachment A RFQ/SOW for a complete listing of requirements/quantities): I LASER TRAINING SIMULATOR SYSTEM II SIMULATION TRAINING CENTRE - TRAINING KITS III INSTALLATION/TRAINING – ONSITE INTERNATIONAL Delivery The vendor is responsible for the delivery of all items. The vendor shall consolidate the entire shipment to prevent loss and misdirection. Entire shipment must be consolidated at the origin and shipped consolidated, partial shipments are not accepted by post due to the Serbian customs donation regulations. Entire shipment must be consolidated under one AWB or CMR. Any lost or damaged items during shipment shall be replaced by the contractor upon notification. Packaging and preservation shall be IAW best commercial practices to enable shipment to final destination in Serbia to the address specified (see Attachment A RFQ/SOW), without repacking or incurring damage during shipment and handling. Delivery shall be made FOB Destination as soon as possible but not later than 90 days from the date of contract award. Submission Requirements (please see details in the Attachment A – RFQ/SOW) Evaluation Criteria (please see details in the Attachment A – RFQ/SOW) After initial evaluation of quotes, the Contracting Officer may negotiate final terms with one or more contractors of the Government’s choice before issuing a purchase order. The Contracting Officer will not negotiate with any contractors other than those of the Government’s choice and will not use the formal source selection procedures described in FAR Part 15. The Government may perform a comparative evaluation to select the contractor that provides the best value, considering the evaluation factors below. The Contracting Officer may issue a purchase order to other than the contractor with the lowest proposed price. The Government will consider the following factors when selecting contractors for award. The following factors shall be used to evaluate quotes: 1) Technical Specifications: Quote must meet or exceed required technical specifications. Compliance with all required features (to include realism of the training, system flexibility, and performance-measurement tools). Quote meets warranty term requirements. Quote verifies compliance with all requested equipment/quantities, utilizing Exhibit A, “Technical Specs”. 2) Delivery Timeline. 3) International Deployment Experience and Maintenance/Support Coverage in Europe: The entity demonstrating International Deployment Experience and Maintenance/Support Coverage in Europe. 4) Past Performance: The entity demonstrates relevant past performance in at least three (3) contracts of similar or superior characteristics to those of this project. 5) Price: The overall price will be considered, and the lowest price is favorable. | - | Combined Synopsis | 11/23/2026 |
This requirement is a 100% Small Business Set-Aside. See attached Combined Synopsis / Solicitation and Statement of Need. | - | Combined Synopsis | 11/16/2026 |
| - | Awarded | Open | |
Airsoft Rifles | - | Combined Synopsis | 08/11/2026 |
Additional Details
Solicitation Number
191NLE20Q0068
Archive Date
Jul 18, 2020
Place of Performance Country
COL
Office Address
WASHINGTON, DC, 20520