Electrically Operated Breaker Service

Pre-Solicitation Notice                                                           Dated February 13, 2026

ACTION CODE:

Pre-Solicitation

DATE POSTED:

February 13, 2026

CLASSIFICATION CODE:

H159 - QUALITY CONTROL - ELECTRICAL AND ELECTRONIC EQUIPMENT COMPONENTS

NAICS CODE:

238210 - Electrical Contractors and Other Wiring Installation Contractors.

CONTRACTING OFFICE ADDRESS:

U.S. Embassy Tashkent

5 Moykurgon Street

Tashkent, 100093

Uzbekistan

SUBJECT:

Electrically Operated Breaker Service.

PROPOSED SOLICITATION NUMBER:

19UZ8026Q0010       

CLOSING RESPONSE DATE:

April 2, 2026

PRIMARY POINT OF CONTACT: 

Joseph Anderson

Contracting Officer

Phone: +99878 1205450

Fax: +99878 1206335

TashkentGSOProcurement@state.gov

SECONDARY POINT OF CONTACT:

Shukhrat Arifdjanov

Procurement Supervisor

Phone: +99878 1205450

Fax: +99878 1206335

ArifdjanovSS@state.gov

PLACE OF PERFORMANCE:

Tashkent, Uzbekistan

DESCRIPTION:

Please note this solicitation is not ready to be issued as of this date. The Embassy of the United States in Uzbekistan will launch the solicitation on the https://uz.usembassy.gov/embassy/tashkent/procurement-and-contracting/ website when it is available.

All responsible sources may submit an offer, which shall be considered. The Government plans to issue the solicitation on March 2, 2026.

The United States Embassies: Tashkent in Uzbekistan require professional services and contractor cost proposals to perform preventive maintenance services of the facility’s electrical switchgear(s). 

Tier III breaker maintenance is defined as: Visual and mechanical inspection by the Original Equipment Manufacturer (OEM) to ensure the proper operation of all factory and vender installed meters, breakers, controls, and remote power monitoring equipment associated with the switch gear. Inspection of the entire switchgear for loose parts, connections, and functioning indicator lights. Cleaning, wiping down and vacuuming of each cradle compartment, inside and outside cabinets.

Preforming testing on electrically operated breakers with appropriate breaker test equipment. Racking breakers out and in. Lubricating all lubrication points per manufacturers recommended procedures and timetables.

The approved contractor must provide a Factory Certified Technician (OEM) with a minimum of five years breaker maintenance experience for the corresponding make of breaker(s) being serviced, for example, Eaton to service Eaton, Schneider to service Schneider and ABB to service GE/ABB etc. to perform the factory service work on the United States Government switchgear circuit breakers and equipment. These qualified technicians are required to be on-site for the servicing of the switchgear breakers and must be accompanied by one Master or Journeyman electrician for the switchgear shutdown and servicing.  Credentials as proof of training and valid electrical licenses must be provided to the COR prior to the execution of the work. The requirement for electrical safety training also applies to this contract.

Advance payments are not authorized.

Electronic Submission/Responses:

 

Electronic offers will be accepted.  Please email your offer to the contracting office listed in this notice prior to the response date and time. 

All contractors have to be registered in the SAM (System for Award Management) Database https://www.sam.gov  prior to contract award pursuant to FAR provision 52.204-7. Therefore, prospective offerors are encouraged to register prior to the submittal of quotations/proposals. 

The guidelines for registration in SAM are also available at:

https://www.fsd.gov/fsd-gov/learning-center-system.do?sysparm_system=SAM

ARCHIVE POLICY:

Automatic, on a specified date.

ARCHIVE DATE:

April 2, 2026.

SET ASIDE:

N/A

Is This a Recovery and Reinvestment Act Action?

No

Allow Vendors to Add/Remove From Interest Vendors:

Yes

Allow Vendors to View Interested Vendors List:

No