GovChime
Notice ID: b6e7bf0829d74c8781c0293a239b4adcSpecial Notice

HAMILITON Steering Actuator, Overhaul

Archived on February 3, 2025. Original response deadline: . Full description on SAM.gov.

Overview

Response deadline
8:00 AM UTC−08:00
Posted
January 23, 2025
Notice type
Special Notice
NAICS
336611: Ship Building and Repairing
Agency
Department of Homeland SecurityUS COAST GUARD

Notice details

Office
SFLC PROCUREMENT BRANCH 2(00085)
Place of performance
North Charleston, SC, 29405
Last updated
Jan 23, 2026

Identifiers

Solicitation number
70Z085Q250002117
Notice ID
b6e7bf0829d74c8781c0293a239b4adc

Description

this item is set to be awarded sole source 56100_TAB_0125_753 ITEM 1: Steering Actuator, Overhaul 1. SCOPE 1.1 Intent. This work item describes the requirements for the Contractor to overhaul the rotary vane steering actuator assembly for the starboard steering system. 1.2 Government-furnished property. MTI ITEM DESCRIPTION NSN/PN QTY N Actuator Overhaul Kit NSN: 2530-01-699-0680 PN: RRM000445315 2 ea. N Hydraulic Coupling Kit NSN: 2530-01-699-0654 PN: RRM000444570 2 ea. 2. REFERENCES Coast Guard Drawings Coast Guard Drawing 750-WMSL_100_44, Rev K, Unit 3320 Struct - Inner Bottom 2nd Deck FR 89-98 (ASC100332) Coast Guard Drawing 750-WMSL-243-003, Rev B, Shipping & Unshipping of Propulsion Shafting (ASC243004) Coast Guard Drawing 750-WMSL-556-004, Rev E, Steering Gear Hydraulic Diagram (ASC556003) Coast Guard Drawing 750-WMSL-556-022, Rev H, Steering Gear and Stern Gate Hydraulic Piping - Unit 3330 (ASC556333-HY) Coast Guard Drawing 750-WMSL-561-001, Rev D, Steering Gear Foundation (ASC561001) Coast Guard Drawing 750-WMSL-562-002, Rev C, Rudder (ASC562002) Coast Guard Drawing 750-WMSL-562-003, Rev D, Rudder Support System (ASC562003) Coast Guard Publications Coast Guard Technical Publication (TP) 7182A, SWBS 561, Jan 2022, Steering Machinery Subsystem Operation & Maintenance Manual Coast Guard Technical Publication (TP) 7193, SWBS 561, Jan 2022, Steering System Operations and Maintenance Manual Surface Forces Logistics Center Standard Specification 0000 (SFLC Std Spec 0000), 2022, General Requirements Surface Forces Logistics Center Standard Specification 0740 (SFLC Std Spec 0740), 2022, Welding and Allied Processes Surface Forces Logistics Center Standard Specification 3041 (SFLC Std Spec 3041), 2022, Shipboard Electrical Cable Test Surface Forces Logistics Center Standard Specification 5000 (SFLC Std Spec 5000), 2022, Auxiliary Machine Systems Surface Forces Logistics Center Standard Specification 6310 (SFLC Std Spec 6310), 2022, Requirements for Preservation of Ship Structures Other References International Standard Organization (ISO) 4406, 2021, Hydraulic Fluid Power - Fluids - Method for Coding Level of Contamination by Solid Particles Kongsberg Maintenance Manual DMN000278736, Rev C, Kongsberg Steering Gear Type SR and SV MIL-STD-419, Sept 2021, Cleaning and Protecting Piping Tubing, And Fittings for Hydraulic Power Transmission Equipment 3. REQUIREMENTS 3.1 General. 3.1.1 CIR. None. 3.1.2 Tech Rep. The Contractor must provide the services of Tech Reps in accordance with the following subparagraphs. 3.1.2.1 The Contractor must provide the services of an OEM authorized/ licensed Tech Rep for the Kongsberg steering actuator to accomplish the following on site: Provide manufacturer's proprietary information, software, and tools pertinent to the equipment/system. Assist with proper repair methods and ensure compliance with manufacturer's procedures and standards during disassembly, inspection, repair, modification, calibration, and reassembly of the equipment/system. Perform all actual repair work on the actuator. 3.1.2.1.1 Ensure the Tech Rep is an OEM Certified Representative for the system/equipment stated above and demonstrated on their r sum . 3.1.2.2 Tech Rep. The Contractor must provide the services of a Qualified Technical Representative who is familiar with the WMSL Steering System Hydraulic Power Units to accomplish the following on site: Advise on manufacturer's proprietary system information. Ensure compliance with manufacturer's procedures and standards during system disassembly, inspection, repair, modification, calibration, and reassembly of the equipment/system as applicable. 3.1.2.2.1 Ensure the Tech Rep has experience with the system/equipment stated above and demonstrated on their r sum . 3.1.2.2.2 Submit the name and r sum of the Tech Rep to the COR at the Arrival Conference. 3.1.3 Protective measures. The Contractor must furnish and install all protective measures in accordance with SFLC Std Spec 0000, paragraph 3.3.3 (Vessel component, space, and equipment protection). 3.1.3.1 Protection of fine surfaces. The Contractor must protect all fine surfaces in accordance with SFLC Std. Spec 5000. 3.1.3.2 Hydraulic system contamination protection. The Contractor must maintain existing hydraulic cleanliness in accordance with SFLC Std. Spec 5000. 3.1.3.3 Maintain the strictest standards of cleanliness in accordance with MIL-STD-419 while hydraulic system is open. Work on the steering hydraulics is not permitted while any blasting, grinding, welding, etc. is being performed in, or adjacent to, the steering gear space. 3.1.3.4 Hatch opening must be covered and roped off to prevent a falling hazard to personnel when not in use. NOTE Plastic bags may be used only when arrangement or configuration prevents the use of the other sealing methods specified above. 3.1.4 Interferences. The Contractor must handle all interferences in accordance with SFLC Std Spec 0000, paragraph 3.3.5 (Interferences). Known interferences include, but are not limited to the following: Access plate (BERP) located above the port and starboard steering actuator. Piping Electrical wires Padeye plate covers Rudder support covers Hydraulic Oil (approx. 560 gals.) Overhead Ventilation Ducts Insulation Pipe hangers/brackets NOTE Coast Guard personnel will operate all shipboard machinery and equipment. 3.2 Operational test, initial. Prior to commencement of work, the Contractor must, under the direction of the OEM Tech Rep, witness Coast Guard personnel perform an initial operational test of all items or shipboard devices to be disturbed, used, repaired, or altered, to demonstrate existing operational condition. Perform the following inspections. Use Data sheet No. 1 (section 4 of this WI) to record results for Starboard actuator only. Submit a CFR. 3.2.1 Verify that all rudder angle indicators (manual indicator on actuator, MCMS indicator, local indicator, and remote indicators on bridge) must be within a 2-degree tolerance throughout range of motion. WARNING Special care should be taken not to hold the rudder hard over for more than a few seconds at a time to avoid overheating the system. 3.2.2 Starboard Steering Gear: In the presence of the Coast Guard inspector, place the 1A HPU online, with the controller set to REMOTE , cycle the rudder from Zero to Port (hard-over), from Port to Starboard (hard-over), from Starboard to Port (hard-over) and from Port to Zero. On the Port to Starboard and Starboard to Port transitions, record the time from 30 degrees on one side to 30 degrees on the other side (speed should be 3 degrees/second or 20 (+/-1) seconds total). With the rudder at Zero degrees and the HPU running, inspect all hoses, fittings and seals for leakage. 3.2.3 Set the steering controller to LOCAL . Using the pushbuttons operators on the pump, cycle the rudder from Zero to 15 degrees Port, from 15 degrees Port to 15 degrees Starboard and from 15 degrees Starboard to Zero. It is not necessary to record times on this evolution this portion of the test only demonstrates that local control can be achieved. Record the result as SAT or UNSAT. 3.2.4 Switch to 1B HPU and perform the same tests to complete the Starboard Steering Gear System test. Note The Cutter is currently outfitted with recessed padeyes as located on CG Drawings 750-WMSL_100_44 and 750-WMSL-243-003 and are in place in the hull above each propeller and rudder. Padeye numbers are 22, 23, 24, and 25 as identified on Coast Guard Drawing 750-WMSL-243-003. Access covers for the recessed padeyes are not required to be reinstalled. Each rudder weighs approximately 12,000 lbs. 3.3 Rudder support. The Contractor must ensure the rudder has been supported in place to allow repairs of the steering actuator assembly. Coast Guard Divers will remove metal plate covers to access the recessed padeyes above each rudder. The Contractor must pull test all existing recessed padeyes to 150% of their maximum expected working load for 10 minutes. In no case may a padeyes expected working load (a) exceed the tabulated maximum working load for the padeyes size or (b) exceed the structures (that padeye is attached to) ability to carry the load. At conclusion of the pull test, visually inspect each padeye for damage. NOTE The centerline of the rudder post is located forward of Frame 96, above the stern gate utility room and forward of an inaccessible void. If additional padeyes are necessary, it may be necessary to clean and gas free these spaces. 3.4 Hydraulic reservoir inspection. The Contractor must take oil samples for testing of existing oil from each reservoir and send out for analysis. Label and retain one extra oil sample from each system for back-up testing if necessary. Drain all 2135 TH hydraulic oil from the HPU actuators and reservoirs (approximately 550 gallons total), and dispose of in accordance with all state, local and federal regulations. Provide CFR with test results. For steering gear hydraulic system details, see Coast Guard Drawings 750-WMSL-556-004 and 750-WMSL-556-022. 3.4.1 Remove access covers from reservoirs and storage tanks. Take samples of any heavy sludge or particulate matter in the tanks. Remove all sludge and debris and wipe down with lint free rags. If any metallic debris (metal filings, shavings, babbitt) is present, notify the Coast Guard Inspector immediately. 3.4.2 When all tanks are thoroughly clean, and just prior to closure ensure all foreign objects have been removed (e.g. rags, caps, towels, plugs). Contractor must present these areas to the Coast Guard Inspector, then close in the presence of the Coast guard inspector. Install new gaskets. 3.5 Steering actuator disassembly and inspection. The Contractor must, under the direction of or performed by the OEM Tech Rep support, overhaul the Starboard steering actuators in accordance with OEM procedures. Rudder foundation, rudder stock, and rudder support system are shown on CG Dwgs 750-WMSL-561-001 and 750-WMSL-562-003. At a minimum, the Contractor must renew the following parts: Piston Seals HP Seals and Backing Strips LP Seals Bearing Shells O-rings 3.5.1 Collect and dispose of all drained fluids in accordance with all federal, state, and local regulations. 3.5.2 Prior to disassembly, wipe down the exterior of the actuator assembly and the general area near the actuator to remove dirt and contaminants. Maintain a clean environment when working around open hydraulic equipment. 3.5.3 Actuator internal inspection. Inspect the interior of the actuators (including, but not limited to, the piston, piston dividers, upper and lower housings, hydraulic coupling, rotor, and rudder stock) for any indications of wear or damage. Submit a CFR documenting the existing condition of the actuators. 3.5.4 During final installation of the actuator, ensure the rudder and rudder stool are aligned, and the actuator and helm are set at 0 degrees. WARNING Foreign materials present a high risk of severe damage to steering gear system. Extra precautions are required to ensure cleanliness of the hydraulic system. Note Suction strainers are located inside the service tanks. 3.6 Filters and strainers, renew. The Contractor must renew the return, charge, and servo filters on each of the Starboard HPUs. Close up filter housings and torque fasteners in accordance with Chapter 5.3 of CG Tech Pub 7182A. Renew the suction strainers and reservoir filter breather on each HPU. 3.7 Manifold and valve inspection and testing. The Contractor must clean, inspect and test the hydraulic manifold and valves (i.e. control, relief, and locking valves) for the starboard system. Clean and visually inspect all parts for defects, deterioration, dirt, scale, rust, grease, and foreign material. Submit a CFR. NOTE Hydraulic hoses life is 12 years 3.8 Hose inspection. The Contractor must visually inspect the condition of all flexible hoses identified in Tables 1 and 2 and submit a CFR with the following information. Hoses that require renewal will be subject to a Change Request. Hose physical condition Service life dates (date for required hose renewal; if not specified, add 12 years to installation date) TABLE 1 STBD STEERING GEAR (COMPARTMENT: 2-94-1-E) Hose Serial # Length (in.) Size (in.) Part Number Fitting #1 Fitting #2 Test Pressure (psi) SG-F-001 20 1 F20606-16-16-16C-20.00 Female JIC Female JIC 200 SG-F-002 26 1/2 F20606-8-8-8C-26.00 Female JIC Female JIC 375 SG-F-003 49 2 2651-32 Female JIC Male CPV 5000 SG-F-004 35 2 2651-32 Male CPV Male CPV 5000 SG-F-005 31.5 3/4 F20606-12-12-12C-31.50 Female JIC Female JIC 200 SG-F-006 43 2 2651-32 Male CPV Male CPV 5000 SG-F-007 43 2 2651-32 Male CPV Male CPV 5000 SG-F-008 26.5 3/4 F2060606-12-12-12C-26.50 Female JIC Female JIC 200 SG-F-009 32 1/2 F2060606-8-8-8C-32.00 Female JIC Female JIC 375 Table 2 Port Steering Gear (COMPARTMENT: 2-94-2-E) Hose Serial # Length (in.) Size (in.) Part Number Fitting #1 Fitting #2 Test Pressure (psi) SG-F-011 20 1 F20606-16-16-16C-20.00 Female JIC Female JIC 200 SG-F-012 26 1/2 F20606-8-8-8C-26.00 Female JIC Female JIC 375 SG-F-013 31.5 3/4 F20606-12-12-12C-31.50 Female JIC Female JIC 200 SG-F-014 49 2 2651-32 Female JIC Male CPV 5000 SG-F-015 35 2 2651-32 Male CPV Male CPV 5000 SG-F-016 26.5 3/4 F2060606-12-12-12C-26.50 Female JIC Female JIC 200 SG-F-017 43 2 2651-32 Male CPV Male CPV 5000 SG-F-018 43 2 2651-32 Male CPV Male CPV 5000 SG-F-019 32 1/2 F2060606-8-8-8C-32.00 Female JIC Female JIC 200 3.9 Hydraulic oil refilling. The Contractor must refill the reservoirs with hydraulic oil per MIL-H-17672, symbol 2135, in accordance with CG Tech Pub 7182A. The Contractor must filter new hydraulic oil in accordance with SFLC Std Spec 5000, paragraph C2.1.2 prior to entry into the Cutters tanks or system. Cleanliness of oil must be ISO 4406 Cleanliness Code of 17/14 or better. NOTE Coast Guard personnel will operate all shipboard machinery and equipment. If covered by a separate work item, final testing of the steering system is only required to be performed once during this availability. 3.10 Operational test, post repairs. After completion of work and in the presence of the Coast Guard Inspector, the Contractor must thoroughly test and demonstrate the equipment listed below to be in satisfactory operating condition. Use Data sheet no. 2 (section 4 of this WI) to record results for Starboard actuator only. Submit a CFR. 3.10.1 Verify that the rudders operate throughout their full range with no indications of binding and appear smooth during operation. 3.10.2 All rudder angle indicators (manual indicator on actuator, MCMS indicator, local indicator, and remote indicators on bridge) must be within a 2-degree tolerance throughout range of motion. 3.10.3 The Contractor must perform the initial startup procedures in accordance with Coast Guard TP 7182, Paragraph 7-2. Upon completion, verify that the relief valves are properly set in accordance with Table 3. TABLE 3 relief valves sERVICE DESCRIPTION Set Point (PSIG) Pump Main System Relief Valve 1530 25 Relief Valve (Charge) 217 25 Relief Valve (Servo) 1450 25 Cross-line Relief Valve 1580 25 Warning Special care should be taken not to hold the rudder hard over for more than a few seconds at a time to avoid overheating the system. 3.10.4 Starting with the Starboard Steering Gear, and in the presence of the Coast Guard inspector, place the 1A HPU online, with the controller set to REMOTE , cycle the rudder from Zero to Port (hard-over), from Port to Starboard (hard-over), from Starboard to Port (hard-over) and from Port to Zero. On the Port to Starboard and Starboard to Port transitions, record the time from 30 degrees on one side to 30 degrees on the other side (speed should be 3 degrees/second or 20 (+/-1) seconds total). With the rudder at Zero degrees and the HPU running, inspect all hoses, fittings and seals for leakage. 3.10.5 Set the steering controller to LOCAL . Using the pushbuttons operators on the pump, cycle the rudder from Zero to 15 degrees Port, from 15 degrees Port to 15 degrees Starboard and from 15 degrees Starboard to Zero. It is not necessary to record times on this evolution this portion of the test only demonstrates that local control can be achieved. Record the result as SAT or UNSAT. 3.10.6 Switch to 1B HPU and perform the same tests to complete the Starboard Steering Gear System test. 3.10.7 The Contractor must perform the Internal Leakage Test per paragraph 7.10 of the Kongsberg Maintenance Manual DMN000278736 for both port and starboard actuators. Measure the total leakage during each separate segment of testing (Port to Starboard hard-over, hard-over Starboard, Starboard to Port hard-over, and hard-over Port) and submit the results via CFR. 3.11 Oil sample analysis. The Contractor must take oil samples for testing of existing oil from each reservoir and send out for analysis to demonstrate cleanliness has been maintained. Submit a CFR with the oil sample analysis report. 3.12 Touch-up preservation. The Contractor must prepare and coat all new and disturbed surfaces to match existing adjacent surfaces in accordance with SFLC Std Spec 6310, paragraph 3.1.13 (Touch-ups and minor coating repairs.) 4.0 Place of performance- CGC HAMILTON in Charleston SC. 5.0 Period of performance- 17 FEB 2025 28 FEB 25 6.0 Points of Contact. USCG-SFLC-LRE PL Asset Management: CWO Matthew Temple, matthew.temple@uscg.mil, 510-460-8195

Full description on SAM.gov

Award Overview

No prior contract identified

No prior award matched this notice's agency, NAICS, place of performance and PSC within 18 months. It may be a new requirement.

Contacts

Documents

Showing 1 of 1 items

Document
Source
Agency
Posted Date
File Size
Actions
Special NoticeUS COAST GUARDJan 23, 2025-

Lifecycle

Solicitation:70Z085Q250002117
  1. Special NoticeCurrentJan 23, 2025

    HAMILITON Steering Actuator, Overhaul

    Notice b6e7bf0829d74c8781c0293a239b4adc on SAM.gov

Similar Opportunities

Title
Match
Phase
Deadline
This is a Request for Quote (RFQ) for the Fiscal Year Quarter (FYQ) 3, Fiscal Year (FY) 27 Dockside Repairs of United States Coast Guard Cutter USCGC HAMILTON (WMSL-753), home moorage North Charleston, SC. Work will include ship repair, maintenance, modifications, and associated logistics and supporting efforts to facilitate the work in accordance with the: Specification HAMILTON (WMSL-753) REV0. Period of Performance: 20 April 2027 – 20 August 2027 Place of Performance: Onboard USCGC HAMILTON (WMSL-753), North Charleston, SC. Attachments: Attachment A _ Specification HAMILTON (WMSL-753) REV0 Attachment B_ Pricing Schedule HAMILTON DS FQ3 FY27 Attachment C_ Request for Clarification HAMILTON FY27 FQ3 Attachment D_ Past Performance Form Attachment E _ FLETC Base Access and Pier Laydown HAM DS Attachment F _ Non-Disclosure Agreement. Attachment G_ HAMILTON DS FQ3 FY27 Provisions and Clauses Attachment H_ SF 1449_Sol. 70ZU0227QLREP0001
-Combined Synopsis12/10/2026
-AwardedOpen
This is a combined synopsis/solicitation for commercial items, prepared in accordance with the format in subpart 12.6 of the FAR and as supplemented with additional information included in this notice. This announcement constitutes only solicitation; quotes are being requested and a separate written solicitation will not be issued. Solicitation number 52000PR260001597 applies and is used as a Request for Quote (RFQ). This solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 2024-05, effective, 22 May 2024. It is anticipated that a competitive price purchase order shall be awarded as a result of this synopsis/solicitation. All responsible sources may submit a quotation, which if timely received, shall be considered by this agency. The U.S. Coast Guard, Surface Forces Logistics Center (SFLC) intends to award a Firm Fixed Price Purchase Order. No down payments or advanced payments will be made to the awarded vendor. Vendor shall ensure they can secure funding for this order until delivered and received by the US Coast Guard. Payment will be made by Government Purchase order (Net 30) and the vendor shall assume financial responsibility until the order is accepted and received by US Coast Guard. Payment of the work is authorized to be submitted as work is completed but must be approved by the Contracting Officer First. Basis for Award: This solicitation is based on FAR 13 – Simplified Acquisition Procedures and quotes will be reviewed and awarded on a Lowest Priced Technically Acceptable basis per the solicitation. Past performance will only be reviewed for “responsibility” basis per FAR 9.1. There are no adjectival ratings nor will award be based on a best value tradeoff basis. All quote’s will be evaluated for who meets all the technical requirements, next who meets our deadlines and finally what is the lowest cost. All quotes shall be emailed to SKC Bryan Duffey via Bryan.A.Duffey@USCG.MIL and shall be received no later than 26 December 2025 10:00AM (Eastern). All emailed quotes shall have 52000PR250001597 in the subject of the email. ITEM 1: FM-200 Cylinder Replace Place of Performance: US Coast Guard 196 Tradd St Charleston, SC 29401 Invoicing In IPP It is now a requirement that all invoicing for Purchase Orders will now be entered and processed through https://www.ipp.gov. FAR Clauses This order is subject to but is not limited to the following Federal Acquisition Regulations: FAR Clauses This order is subject to but is not limited to the following Federal Acquisition Regulations: 52.204-24 Representation Regarding Certain Telecommunications and Video Surveillance Services or Equipment. 52.204-26 Covered Telecommunications Equipment or Services-Representation. 52.212-1 Instructions to Offerors—Commercial Products and Commercial Services. 52.212-3 Offeror Representations and Certifications—Commercial Products and Commercial Services. 52.204-23 Prohibition on Contracting for Hardware, Software, and Services Developed or Provided by Kaspersky Lab Covered Entities. 52.204-25 Prohibition on Contracting for Certain Telecommunications and Video Surveillance Services or Equipment. 52.212-5 Contract Terms and Conditions Required To Implement Statutes or Executive Orders—Commercial Products and Commercial Services.
-Combined Synopsis12/26/2026
USCGC LEGARE Pelican Hook & Detachable Links This is a combined synopsis/solicitation for commercial products and commercial services prepared in accordance with the format in FAR Subpart 12.6, as supplemented with additional information in this notice. This announcement constitutes the only solicitation; quotations are being requested and a written solicitation will not be issued. This solicitation is issued as a Request for Quotation (RFQ) Number 52000QR270000165. This procurement will be processed in accordance with FAR Part 12. The North American Industry Classification System (NAICS) is 336611. The small business size standard is 1300. This is a total small business set aside; all responsible small business sources may submit quotations that will be considered. This synopsis/solicitation is issued pursuant to FAR 13.106-1(b), and the resultant purchase order will be awarded on a firm-fixed price basis using simplified acquisition procedures in accordance with FAR 13. THE UNITED STATED COAST GUARD SURFACE FORCE LOGISTICS CENTER REQUEST THE CONTRACTORS TO PROVIDE PRICING FOR THE FOLLOWING REQUIREMENT: CGC Legare Pelican Hooks & Detachable links. A. REQUIREMENT: 1. The contractor shall provide Pelican Hooks & Detachable links. See Attached SOW. 2. DELIVERY LOCATION (FOB Destination) Coast Guard Yard 2401 Hawkins Point RD Curtis Bay MD, 21226 3. REQUIRED DELIVERY DATE: July 01, 2027 Interested Vendors shall provide product/service details, Product Data Sheet, and cost breakdown IAW SOW for technical review. Vendors shall provide a detailed cost breakdown to include all the specifications to be reviewed by a technical rep. NOTE: The USCG/Government reserves the right to Award on an All or None Basis, i.e., the Government may issue a Purchase Order (PO) to the offeror that submits the lowest aggregate price, rather than issue a PO to each offeror based on the lowest quotation on each item. As stated below, the provision at FAR 52.212-2- Evaluation-Commercial Products and Commercial Services-applies with the following addenda: Award of a contract will be based on the following criteria: The purchase order will be awarded as a firm-fixed price contract using simplified acquisition procedures in accordance with FAR Part 13. 1. Please provide any warranty information. 2. Vendors MUST have an active registration in www.sam.gov The USCG/Government intends to award a purchase order resulting from this synopsis/solicitation to the responsible contractor whose quote conforms to the solicitation and is most advantageous and the best value to the Government, price and other factors considered. The Government will utilize the simplified evaluation procedures outlined in FAR 13.106-2. Please Note: Interested Offerors having the expertise as required are invited to submit a Firm Fixed Price quotation that will be considered by the agency. Quotations must be submitted on company letterhead stationery and must include the following information: (1) Cost Breakdown (2) Unit Cost (3) Extended Price (4) Total Price (5) Payment Terms (6) Discount offered for prompt payment (7) Company Unique Entity ID (UEI) and Cage Code. Quotes must be received no later than 17 November 2026 at 1 P.M. Eastern Standard Time. Email quotes are acceptable and shall be sent to Mr.Cornelius Claiborne at: Cornelius.n.Claiborne@uscg.mil and carbon copy Contracting Officer CWO2 Sean W. Hoy at Sean.W.Hoy@uscg.mil. Any questions or concerns regarding any aspect of the RFQ must be forwarded to Mr. Cornelius Claiborne at email address – Cornelius.n.Claiborne@uscg.mil and carbon copy Contracting Officer, CWO2 Sean W. Hoy via email Sean.W.Hoy@uscg.mil. The following FAR Clauses and Provisions apply to this acquisition: FAR 52.204-7 – System for Award Management (Nov 2024). To facilitate payment, contractors shall be registered in SAM.gov with an active Unique Entity Identifier (UEI) prior to submitting a quotation. A UEI and SAM registration can be obtained via https://www.sam.gov. FAR 52.212-1 - Instructions to Offerors – Commercial Products and Commercial Services (Sep 2023) FAR 52.212-2 - Evaluation - Commercial Products and Commercial Services (Nov 2021) Award will be made to the Offeror proposing the Best Value to the Government considering specification, price, past performance and quality. FAR 52.212-3 - Offeror Representations and Certifications - Commercial Products and Commercial Services (Oct 2025) to include Alt I (Feb 2024). Offeror shall complete annual representations and certification electronically via the System for Award Management (SAM) website accessed through https://www.sam.gov. FAR 52.212-4 - Contract Terms and Conditions - Commercial Products and Commercial Services (Nov 2023) FAR 52.212-5 - Contract Terms and Conditions Required to Implement Statutes or Executive Orders - Commercial Products and Commercial Services (Mar 2026) FAR 52.252-2 - Clauses Incorporated by Reference (Feb 1998) The following clauses, and others as directed by the Contracting Officer as applicable, shall apply to this awarded contract: FAR 52.219-6 - Notice of Total Small Business Set-Aside (Nov 2020 FAR 52.219-28 - Post-Award Small Business Program Rerepresentation (Feb 2024 FAR 52.222-3 - Convict Labor (Jun 2003) FAR 52.222-19 - Child Labor Cooperation with Authorities and Remedies (Mar 2026) (E.O.13126). FAR 52.222-35 - Equal Opportunity for Veterans (Jun 2020) (38 U.S.C. 4212). FAR 52.222-36 - Equal Opportunity for Workers with Disabilities (Jun 2020) (29 U.S.C. 793). FAR 52.222-37 - Employment Reports on Veterans (Jun 2020) (38 U.S.C. 4212). FAR 52.222-50 - Combating Trafficking in Persons (Oct 2025) (22 U.S.C. chapter 78 and E.O. 13627). FAR 52.225-1 - Buy American Supplies (Oct 2022) (41 U.S.C. chapter 83). (51) 52.225-13, Restrictions on Certain Foreign Purchases (Feb 2021) (E.O.’s, proclamations, and statutes administered by the Office of Foreign Assets Control of the Department of the Treasury). FAR 52.232-33 - Payment by Electronic Funds Transfer - Systems for Award Management (Oct 2018) FAR 52.233-3 - Protest After Award (Aug 1996) FAR 52.233-4 - Applicable Law for Breach of Contract Claim (Oct 2004) *The above clauses are incorporated by reference, entire clause(s) available at https://acquisition.gov. NOTICE TO OFFERORS CONCERNING REPRESENTATIONS AND CERTIFICATIONS: This solicitation contains FAR Clause 52.204-7, System for Award Management and FAR Provision 52.204-8, Annual Representations and Certifications. In accordance with FAR 4.1201 (a), prospective contractors shall complete electronic annual representations and certifications via SAM accessed through https://www.sam.gov. Please ensure completion prior to submitting a quotation. Paragraph (b) of FAR 52.204-8 applies. System updates may lag policy updates. The System for Award Management (SAM) may continue to require entities to complete representations based on provisions that are not included in agency solicitations. Examples include 52.222-25, Affirmative Action Compliance, and paragraph (d) of 52.212-3, Offeror Representations and Certifications—Commercial Products and Commercial Services. Additional examples include 52.212-5, Contract Terms and Conditions Required To Implement Statutes or Executive Orders—Commercial Products and Commercial Services, and 52.213-4, Terms and Conditions—Simplified Acquisitions (Other Than Commercial Products and Commercial Services).
-Combined Synopsis11/17/2026
This is a combined synopsis/solicitation of the United States Coast Guard's intent to award 70ZU0327P50204B00 as a BRAND NAME award The Purchase of Forty (40) each; SEAT BOTTOM; P/N: SW-01309; NSN: 2090-01-F15-4282. Assets: 26' TANB. .This determination is in accordance with 13.106-1(b) ONLY ONE BRAND NAME AND NO OTHER SUPPLIES OR SERVICES WILL SATISFY AGENCY REQUIREMENTS. For more information on the circumstances please reference the attached JOTFOC. This announcement constitutes the only solicitation; quotes are being requested and a separate written solicitation will not be issued
-Combined Synopsis11/18/2026

Additional Details

Solicitation Number

70Z085Q250002117

Archive Date

Feb 3, 2025

Office Address

ALAMEDA, CA, 94501