Notice ID: b33ab3741cae75b5b471df654dc234b3Award NoticeAwarded
Atomic Force Microscope
Awarded on September 7, 2018. Full description on SAM.gov.
Awarded tounder 80GSFC18C0134 (source: SAM.gov award notice)• $231.8K
Overview
- Posted
- October 1, 2018
- Notice type
- Award Notice
- NAICS
- 334516: Analytical Laboratory Instrument Manufacturing
Notice details
- PSC
- 66: INSTRUMENTS AND LABORATORY EQPT
- Last updated
- Oct 11, 2026
- Award date
- Sep 7, 2018
- Award amount (SAM.gov award notice)
- $231.8K
Identifiers
- Solicitation number
- 80GSFC18R0049
- Notice ID
- b33ab3741cae75b5b471df654dc234b3
- Award number (PIID)
- 80GSFC18C0134
Description
NASA/GSFC has a requirement for an Atomic Force Microscope (AFM) GSFC Detector Development Laboratory (DDL). The system is used to characterize the geometry and other physical properties of nanoscale structures built in the DDL. The system is suitable for characterizing thin-films on substrates up to 200 mm in diameter. It shall include all necessary software and hardware to enable microscope control and data analysis. The vendor shall provide equipment technical support. NASA/GSFC intends to purchase the items from Bruker Nano, Inc. located at 112 Robin Hill Road, Goleta, CA 93117. Bruker Nano, Inc. is the only known source that can provide an atomic force microscope (Dimension ICON) that meet the technical requirements of the DDL. The Bruker's AFM system is the only system that has a standard, patented, general purpose AC imaging mode that 1) automatically optimizes critical imaging parameters including setpoint, gains, scan rate and Z limit; 2) automatically optimizes these imaging parameters whether imaging in air or in liquids; 3) does not require that the cantilever resonance be "tuned"; 4) has conventional imaging rates (<10 minutes per image); 5) directly controls the tip-sample imaging force down to at least 50 pN; 6) automatically compensates for drift of the deflection signal. Additionally, only the Dimension ICON offers standard AFM operating modes such as Peak force tapping which controls the peak force of the cantilever tip of under 20 pN, as well as to extract sample parameters such as adhesion force and film modulus (1 MPa- 50 GPa). The Government does not intend to acquire a commercial item using FAR Part 12. Interested organizations may submit their capabilities and qualifications to perform the effort in writing to Timothy Lazatin at Timothyjames.s.lazatin@nasa.gov no later than 2:00 pm EST on July 16, 2018. Such capabilities/qualifications will be evaluated solely for the purpose of determining whether or not to conduct this procurement on a competitive basis. A determination by the Government not to compete this proposed effort on a full and open competition basis, based upon responses to this notice, is solely within the discretion of the government. Oral communications are not acceptable in response to this notice. All responsible sources may submit an offer which shall be considered by the agency. NASA Clause 1852.215-84, Ombudsman, is applicable. The Center Ombudsman for this acquisition can be found at http://prod.nais.nasa.gov/pub/pub_library/Omb.html.
Award Overview
Award Number
80GSFC18C0134
Award Amount (SAM.gov award notice)
$231.8K
Award Date
Sep 7, 2018
Awardee
Awardee UEI
HF8BQ45QKKJ3
Original Solicitation
Notice ID: b33ab3741cae75b5b471df654dc234b3
Posted Date: Oct 1, 2018
Original Response Deadline: Not specified
Contract Details
No FPDS record matches this award number at the same department yet
Contract details typically appear within 2-4 weeks after award; DoD awards are published about 90 days after signature.
More From This Vendor
Top 5 most recent
- $31.4KSigned Aug 10, 2026
Contacts
Contracting Officer
Primary Contact
Documents
No documents available.
Lifecycle
Solicitation:
80GSFC18R0049- Pre-Solicitation
- Solicitation
- Awarded
This opportunity has been awarded.
- Pre-SolicitationApr 17, 2018
Atomic Force Microscope
Similar Opportunities
Title | Match | Phase | Deadline |
|---|---|---|---|
Additional Details
Solicitation Number
80GSFC18R0049
Archive Date
Jan 1, 2022