GovChime
Notice ID: 933b39dfb3474dc8914ea781eefd3ccaSpecial Notice

Autonomous Ion Mass Spectrometer Sentry (AIMSS)

Active, responses due . Full description on SAM.gov.

Overview

Response deadline
5:00 PM MST
Posted
August 12, 2026
Notice type
Special Notice
Set-aside
No Set aside used
NAICS
927110: Space Research and Technology
Agency
Department of Energy

Notice details

Office
TRIAD - DOE CONTRACTOR
Place of performance
Los Alamos, New Mexico, 87545
Last updated
Oct 28, 2026
First published
Last updated on SAM.gov

Identifiers

Solicitation number
S-194425
Notice ID
933b39dfb3474dc8914ea781eefd3cca

Description

Satellite measurements of plasma density and temperature help predict the intensity of geomagnetic storms, which can impact satellites, communications, and power systems. Accurate forecasting requires knowledge of plasma composition. However, typical orbital mass spectrometers have difficulty distinguishing between nitrogen (N+) and oxygen (O+) ions due to their similar masses. This limitation makes it difficult to validate modern space weather models, which depend on accurate knowledge of ion composition in near-Earth space. N+ and O+ ions behave differently in space due to differences in their origin, transport, and loss mechanisms. Improving our ability to distinguish between these ions is critical for understanding and predicting space weather.

Advantages

  • High mass resolution enables distinction between ion species that are typically unresolved in space-based measurements (e.g., N+ vs O+)
  • Simultaneous measurement of multiple ion species for improved data collection efficiency
  • Commandable ion throughput allows for high dynamic range without detector saturation
  • Flight-qualified design with near-term on-orbit demonstration on the ISS

Technology Description

The AIMSS instrument uses electric and magnetic fields to sort ions first by energy and then by mass. As ions move through the instrument, different species are separated and spread out across the detector as a spectrum, similar to how a prism separates white light into different colors.

First, incoming ions pass through two electrostatic energy filters (ESAs) located at the front of the sensor. These filters allow only ions within a selected energy range to continue through the instrument. By adjusting the voltage applied to each filter, AIMSS can control how many ions reach the detector and adapt to changing plasma density.

Next, the ions enter a magnetic field section that separates them by mass. Lighter ions are deflected more than heavier ions, causing different ion species to land at different positions on the detector.

The detector records where ions land, allowing the instrument to measure multiple ion species at once and determine their mass and energy.

This design achieves clear separation of closely spaced ion species such as N+ and O+, improving the accuracy of plasma composition measurements.

Market Applications

AIMSS supports both scientific and operational markets:

  • Space Domain Awareness: Monitoring plasma density and composition to attribute spacecraft anomalies and charging events.
  • Space Weather Monitoring and Forecasting : Ion composition measurements of ionospheric plasma to inform space weather models and improve forecasting.
  • Space Station Operations for Lunar and Mars Missions : Monitoring spacecraft health, contamination, and charging during extravehicular activities (EVAs) and docking operations.
  • Department of Defense / Space Force : Compliance with requirements for onboard space environment sensors.

IP Information

This technology is protected under the following intellectual property:

  • U.S. Patent No. 12,476,101 – Ultra-Compact Ion Mass Spectrometer for Space and Laboratory Plasma Measurements (S167645)
  • Patent Pending – Dual Electrostatic Plasma Analyzer for Tunable Energy Resolution and Geometric Factor (S-194425)
  • Reconfigurable High Voltage Power Supply – U.S. Provisional Application No. 63/515,283
  • Electronics Package for Two-Dimensional Imaging Spectrometry (application/patent status to be confirmed)

TRL 6

LA-UR-26-23247

LANL Tech Partnerships: Unlock the Innovative Potential

Los Alamos National Laboratory offers a wide range of cutting-edge technologies and capabilities that may provide your company with a competitive edge in the market and unlock the innovative potential that can enhance, refine, and revolutionize your products.

LANL’s licensing program focuses on moving inventions developed by our researchers to commercial innovations. Patented and patent pending inventions and copyrighted software are available to existing and start-up companies through exclusive and non-exclusive licensing agreements. For specific discussions, please contact licensing@lanl.gov.

Note: This is not a call for external services for the development of this technology.

https://www.lanl.gov/engage/collaboration/feynman-center/partner-with-us/licensing-technology

m.lanl.gov/tech-search

Full description on SAM.gov

Award Overview

No prior contract identified

No prior award matched this notice's agency, NAICS, place of performance and PSC within 18 months. It may be a new requirement.

Contacts

Contracting Officer

Primary Contact

Mike Erickson

Secondary Contact

Lindsay Augustyn

Documents

Files (1)

  • aimss-snapshot-la-ur-26-23247_db417.pdf

    1.2 MBAdded in Special Notice version 1Posted
    Download

Lifecycle

  1. 1
    Version 1Special NoticeCurrent

    Autonomous Ion Mass Spectrometer Sentry (AIMSS)

    Notice 933b39dfb3474dc8914ea781eefd3cca on SAM.gov

Similar Opportunities

Title
Match
Phase
Deadline
AMENDMENT 01 - SUPERSEDES PREVIOUS PUBLICATION. Introduction, paragraph 2 revised. The KSC Research and Technology (R&T) vision is to be a key contributor to NASA’s space technology innovation ecosystem, complementing the expertise and capabilities of other Centers in support of the Artemis Mission. Central to this vision is the expansion of partnerships with academia, private industry, and other government agencies, particularly with institutions whose technical expertise complements KSC’s existing capabilities. Through these collaborations, KSC aims to diversity its user base, enhance competitiveness, broaden research avenues, and cultivate environments that accelerate technological innovation and advancement in a rapidly evolving landscape. **SEE ATTACHMENT FOR FULL DETAILS**
-Special Notice11/20/2026
GasFlow DLP Printing Interface, developed by scientists at Los Alamos National Laboratory, helps resin-based 3D printing systems produce finer details, faster builds and more consistent part quality by controlling oxygen where curing happens most critically. The open-surface approach fits well with bottom-up DLP and related vat photopolymer processes, and it can enhance existing printer designs, as well as new platforms, by improving print fidelity, process stability and material flexibility. How it Works The system adds a second liquid beneath the printable resin inside the vat, creating a stable fluid-fluid interface between the two liquids. This interface is where the resin is polymerized, removing the need to pull the polymerized layer off the surface - an inherent default in the DLP process. The lower liquid is chosen to be an immiscible, high-density fluid, such as a perfluorinated fluid, that is treated with an inert gas and circulated continuously during printing. As it flows beneath the resin and above the transparent vat window, the lower liquid removes oxygen from the resin and introduces inert gas in its place, which reduces oxygen inhibition at the curing zone. With less oxygen interfering with polymerization, projected light can cure smaller features more reliably, more quickly and more uniformly across the part with less bleeding. Technical Description The patented GasFlow DLP Printing Interface is designed for additive manufacturing methods such as DLP, SLA and related photopolymer printing processes. The GasFlow DLP Printing Interface uses a first container or vat with a transparent portion, a first fluid positioned against that transparent portion and a second fluid that serves as the printable resin. The first fluid and second fluid form a fluid-fluid interface, with the first fluid located between the vat window and the resin. A circulation system moves the first fluid through the vat and an associated treatment container by way of conduits and a pumping mechanism. In representative embodiments, the first fluid is a perfluorinated solvent that has been treated with an inert gas such as nitrogen, helium, argon or carbon dioxide. As the treated first fluid circulates, it removes oxygen from resin at the interface and helps replace that oxygen with inert gas, which improves polymerization performance at the print surface. Oxygen in standard resin systems can suppress curing, which means more energy is required than necessary which in turn can create uneven polymerization that leaves parts overcured in some regions and undercured in others making very small features difficult to print. Features below about 50 microns in diameter may fail to print when normal oxygen levels are present. GasFlow DLP Printing demonstrated print speed improvement of at least one-third, with larger gains considered possible under optimized conditions. An added benefit to flowing fluid is that the system can provide temperature-control to help manage heat buildup during printing, which can improve part quality and widen the range of usable resin chemistries. Advantages Produces finer features and higher print resolution Reduces oxygen-related defects during curing Speeds printing compared with standard setups (oxygen exposed) Improves consistency across the part, including edge-to-center uniformity Supports retrofit potential for many bottom-up DLP printers Increases lifetime of liquid resin May enable use of resin chemistries that are otherwise difficult to process because of overheating or curing instability Market Applications Additive Manufacturing (resin 3D printers, printer upgrades, production platforms) Industrial Manufacturing (precision polymer parts, lightweight structures, fabrication tooling) Medical and Dental (custom polymer components, device fabrication, detailed models) Electronics and Microfabrication (fine-feature polymer structures, patterned parts, prototyping) Research and Laboratory Equipment (materials development, process testing, advanced printing systems) Aerospace and Defense (complex geometries, lattice structures, specialty components) TRL 4 US Patent No. 11,911,955 LA-UR-26-29477 LANL Tech Partnerships: Unlock the Innovative Potential Los Alamos National Laboratory offers a wide range of cutting-edge technologies and capabilities that may provide your company with a competitive edge in the market and unlock the innovative potential that can enhance, refine, and revolutionize your products. LANL’s licensing program focuses on moving inventions developed by our researchers to commercial innovations. Patented and patent pending inventions and copyrighted software are available to existing and start-up companies through exclusive and non-exclusive licensing agreements. For specific discussions, please contact licensing@lanl.gov. Note: This is not a call for external services for the development of this technology. https://www.lanl.gov/engage/collaboration/feynman-center/partner-with-us/licensing-technology m.lanl.gov/tech-search
-Special Notice04/06/2027
Single Photon Generation Through Mechanical Deformation Value Proposition PinPoint Photon from Los Alamos National Laboratory gives quantum technology developers something they have long lacked: single photon sources that appear exactly where a designer places them. The approach relies on a wafer-scale film of an ultra-thin semiconductor shaped over precisely patterned tips. Light emitters can therefore be arranged in predictable arrays rather than found by chance. Early testing produced emitters at nearly nine out of 10 tip sites, with stable output for hours and excited-state lifetimes many times longer than those of unstrained material. Hardware teams in secure communications, photonic computing and quantum sensing gain a practical path from laboratory demonstrations to manufacturable chips. Challenges Many emerging quantum technologies need light that arrives one photon at a time. Examples include encryption keys that cannot be intercepted unnoticed and optical quantum computers. Ultra-thin 2D materials such as tungsten diselenide, tungsten disulfide and hexagonal boron nitride can produce such photons, but only from defects that form randomly, with no reliable way to control their location. Earlier attempts to guide emission by patterning the surface underneath the film could not separate the effect of mechanical strain from changes in the surrounding material, so the underlying physics stayed unclear. Most 2D quantum materials have also come from lab-scale methods such as peeling flakes off a crystal, which are unsuitable for large-scale device integration. Secure communication systems further need each site to hold no more than one emitter, a level of control that random defects cannot provide. Problems Solved PinPoint Photon replaces chance with design. A continuous few-layer tungsten diselenide film grown by gas-source chemical vapor deposition is transferred onto an array of ultra-sharp silicon dioxide tips. Each tip bends the film enough to localize emission at its apex. The film sits in a uniform silicon dioxide environment, so the team showed that mechanical bending alone creates the emission sites. That result answers the open scientific question left by earlier studies. The vapor deposition process is compatible with wafer-scale integration, and designers can set tip spacing so that each emitter remains individually accessible to optical systems. The resulting emitters showed no fine structure splitting, a key advance for quantum applications, along with spectral stability and roughly an order of magnitude longer lifetime than free excitons. Measured single photon purity reached about 70% at 3.8 K, with stable emission for up to eight hours. Advantages Places quantum light sources at chosen locations instead of random ones High success rate, with emitters forming at 87% of tip sites in testing Built on a wafer-scale growth process suited to chip-style manufacturing Steady, long-lived light output that held stable for hours Clean emission without the line splitting that complicates many quantum emitters Potentially extends to other 2D materials emitting from the ultraviolet to the infrared Market Applications Quantum Communications (secure key distribution, quantum networks, encrypted links) Quantum Computing (photonic processors, all-optical quantum circuits) Photonic Integrated Circuits and Semiconductors (on-chip light sources, optical signal generation) Sensing and Metrology (magnetic field sensors, temperature sensors) Scientific Instrumentation (quantum optics test sources, research tools for universities and laboratories) TRL 3 U.S. Patent No. 12,237,428 LA-UR-26-29956 LANL Tech Partnerships: Unlock the Innovative Potential Los Alamos National Laboratory offers a wide range of cutting-edge technologies and capabilities that may provide your company with a competitive edge in the market and unlock the innovative potential that can enhance, refine, and revolutionize your products. LANL’s licensing program focuses on moving inventions developed by our researchers to commercial innovations. Patented and patent pending inventions and copyrighted software are available to existing and start-up companies through exclusive and non-exclusive licensing agreements. For specific discussions, please contact licensing@lanl.gov. Note: This is not a call for external services for the development of this technology. https://www.lanl.gov/engage/collaboration/feynman-center/partner-with-us/licensing-technology m.lanl.gov/tech-search
-Special Notice04/06/2027
Imagine loading an irregular block of metal, or a finished curved part, into a single station and walking away with precisely cut samples, no specialized machining expertise required. Scan-to-Sample from Los Alamos National Laboratory makes that possible by weaving 3D scanning, design software and computer-guided cutting into one continuous digital thread, running from the first scan straight through to the finished part. The system captures the true shape of the starting material, however curved or complex, then plans and carries out the cuts on its own, sparing operators the slow, error-prone job of hand-aligning and re-zeroing equipment for every specimen. The payoff is faster turnaround, less wasted material and consistent, repeatable quality, bringing advanced machining within reach of a far wider range of users and parts. How it Works The workflow begins when a scanning device, such as a laser scanner, optical scanner or contact probe, captures the exact geometry of the incoming material or part and produces an accurate digital 3D model. Design software then imports that model, where an operator marks the locations, orientations and sizes of the samples or features wanted, and the software calculates the tool paths needed to reach them. Those tool paths are converted into machine instructions, typically a G-code file, and loaded onto a computer numerical control machine, which secures the material and cuts the specimens by following the programmed paths without manual re-zeroing. After cutting, the finished part can be scanned again and compared against the original model to confirm that every specimen meets the required tolerances. Technical Description At its core, Scan-to-Sample links four cooperating elements: i) a scanning device that records the dimensional, geometric and surface characteristics of the workpiece; ii) an operations device that builds a watertight 3D model and generates the cutting program; iii) a machining apparatus such as a multi-axis CNC mill, turning center, grinder, laser or wire EDM system; and iv) a monitoring apparatus that verifies the outcome. The operations device applies a sample extraction model, which carries the functionality of standard CAD and CAM tools, to the 3D model so as to map sampling locations onto the true contours of the part and to derive the tool paths, cutting tools, spindle speeds, feed rates and fixturing choices suited to the material and its tolerances. Because the pipeline is driven by the scanned geometry rather than by fixed programming, it adapts to each unique part and supports two complementary modes of use. In sampling mode, the system extracts small test specimens from complex, non-linear components such as turbine blades or gear teeth, for mechanical testing and analysis. In fabrication mode, the same approach reads a raw or partially formed blank, billet or bar and produces a finished component from it, giving users an experience similar to the guided interfaces common in additive manufacturing. A closed feedback step compares the machined result against the digital model, allowing the system to flag deviations, take an additional sample or stop safely, which keeps quality consistent across every run. Advantages • Removes the slow, error-prone need to align and re-zero the machine by hand for every sample • Lowers the skill barrier, letting users with little machining experience produce complex parts • Handles irregular and curved stock that is hard to fixture and cut by conventional means • Reduces material waste when many small parts are taken from a single piece • Consolidates scanning, design and machining into one connected workflow • Improves precision, repeatability and sample yield across multiple runs Market Applications • Aerospace and Space Systems (turbine blade sampling, launch and propulsion component fabrication) • Power Generation and Energy (gear and turbine component testing) • Materials Research (mechanical behavior specimens for characterization) • Precision Manufacturing (custom parts from irregular or raw stock) • Automotive (drivetrain and gear inspection) • Quality Assurance and Metrology (dimensional verification and defect analysis) TRL 4 US Patent pending LA-UR-26-29796 LANL Tech Partnerships: Unlock the Innovative Potential Los Alamos National Laboratory offers a wide range of cutting-edge technologies and capabilities that may provide your company with a competitive edge in the market and unlock the innovative potential that can enhance, refine, and revolutionize your products. LANL’s licensing program focuses on moving inventions developed by our researchers to commercial innovations. Patented and patent pending inventions and copyrighted software are available to existing and start-up companies through exclusive and non-exclusive licensing agreements. For specific discussions, please contact licensing@lanl.gov. Note: This is not a call for external services for the development of this technology. https://www.lanl.gov/engage/collaboration/feynman-center/partner-with-us/licensing-technology m.lanl.gov/tech-search
-Special Notice04/02/2027
Value Proposition: ThermaSpin, developed by scientists at Los Alamos National Laboratory, provides a reliable, cost-effective way to measure the flow behavior (viscosity) of extremely hot and reactive liquids, such as molten salts and metals, under realistic operating conditions. Unlike existing solutions that are expensive, complex or poorly suited for low-viscosity fluids, this enclosed high-temperature viscometer delivers high sensitivity, small sample requirements and precise atmospheric control, enabling accurate measurements without exposing materials to air or contamination. This capability is critical for industries such as advanced nuclear energy, thermal energy storage and high-temperature materials processing, where fluid properties directly impact system performance, safety and design. By making these measurements more accessible and practical, the ThermaSpin High-Temperature Viscometer reduces development risk, lowers testing costs and accelerates innovation in next-generation energy and industrial systems. The Challenge: Accurately measuring the viscosity of molten salts and other high-temperature liquids is extremely difficult because these materials exist under harsh conditions—temperatures approaching 1,000°C, high chemical reactivity and sensitivity to air and moisture. Traditional measurement techniques often lack the sensitivity needed for these low-viscosity fluids or require specialized, resource-intensive methods that are not widely accessible. In addition, many approaches demand large sample volumes, which can be impractical or hazardous when working with corrosive or toxic materials. Maintaining a controlled environment during testing further complicates measurements, as even minor contamination can alter results. Together, these challenges create a significant barrier to obtaining reliable data on fluid behavior in systems where precise performance understanding is essential. Problems Solved: ThermaSpin High-Temperature Viscometer addresses these challenges by providing a sealed, high-temperature measurement system that can operate reliably in extreme environments while maintaining strict control over sample purity. Its rotational design, coupled with a highly sensitive torsion-based measurement approach, enables accurate detection of the very low forces associated with low-viscosity molten fluids—something conventional instruments struggle to achieve. The enclosed architecture allows operation under inert or controlled atmospheres, preventing contamination from air or moisture, while also supporting smaller sample sizes to reduce risk and material constraints. By integrating temperature resilience, corrosion compatibility and precise mechanical measurement into a single platform, ThermaSpin overcomes the key technical and practical limitations that have historically restricted viscosity characterization in these demanding conditions. Key Advantages: Extreme temperature capability (~1000°C): Reliable operation for molten salts, metals and other high-temperature fluids High sensitivity for low-viscosity liquids: Accurately captures subtle flow behavior that conventional viscometers miss Sealed, controlled environment: Maintains sample purity by preventing exposure to air and moisture Handles corrosive and hazardous materials: Durable design compatible with chemically aggressive substances and smaller sample sizes No specialized infrastructure required: Eliminates dependence on costly, limited-access techniques like neutron imaging Versatile and integration-ready: Adaptable to multiple applications and compatible with inert atmosphere systems (e.g., glove boxes) Market Applications: Advanced Nuclear Energy: Molten salt reactors (MSRs), fusion systems and fuel cycle development Thermal Energy Storage & CSP: High-temperature heat transfer and storage fluids for renewable energy systems Metallurgy & Metal Processing: Molten metal monitoring in refining, casting and advanced manufacturing Chemical Processing: High-temperature and corrosive fluid handling in industrial chemical production Research & Development: National labs, academia and industry studying thermophysical properties of extreme-condition materials Defense & Government Applications: Controlled characterization of hazardous or sensitive molten materials in secure environments Development Status: TRL 3 US Patent pending LA-UR-26-26227 LANL Tech Partnerships: Unlock the Innovative Potential Los Alamos National Laboratory offers a wide range of cutting-edge technologies and capabilities that may provide your company with a competitive edge in the market and unlock the innovative potential that can enhance, refine, and revolutionize your products. LANL’s licensing program focuses on moving inventions developed by our researchers to commercial innovations. Patented and patent pending inventions and copyrighted software are available to existing and start-up companies through exclusive and non-exclusive licensing agreements. For specific discussions, please contact licensing@lanl.gov. Note: This is not a call for external services for the development of this technology. https://www.lanl.gov/engage/collaboration/feynman-center/partner-with-us/licensing-technology m.lanl.gov/tech-search
-Special Notice04/01/2027

Additional Details

Solicitation Number

S-194425

Archive Date

Aug 15, 2027

Office Address

Columbus, OH, 43201