Notice ID: 917d546a3f89dcf6fea09dea25e49b9bAward NoticeAwarded
A--Hydraulic Conductivity Test Setup
Awarded on September 27, 2012. Full description on SAM.gov.
Awarded tounder N00244-12-P-1358 (source: SAM.gov award notice)• $32.8K
Overview
- Posted
- September 27, 2012
- Notice type
- Award Notice
- NAICS
- 541712: Classification Not Available
Notice details
- PSC
- A: RESEARCH AND DEVELOPMENT
- Last updated
- Dec 3, 2025
- Award date
- Sep 27, 2012
- Award amount (SAM.gov award notice)
- $32.8K
Identifiers
- Solicitation number
- N0024412T0300
- Notice ID
- 917d546a3f89dcf6fea09dea25e49b9b
- Award number (PIID)
- N00244-12-P-1358
Description
STATEMENT OF WORK Fabrication Of Compaction-Mold Permeameter For Measurement Of Hydraulic Conductivity 1.0 SCOPE 1.1 NAVFAC-ESC would like to evaluate a new Cathodic Protection Anode Product, EnvirAnodeTM for benefits in containing cross contamination of underground aquifers. 1.2 The scope of work is to fabricate a full-scale replica of a deep well anode installation to measure water permeability of the EnvirAnodeTM. Specifically the experimental setup should replicate the soil, drilling and filling conditions typical of an anode installation for an ICCP system. 1.3 The setup will allow the user to make quantitative measurements of the water leakage through the anode installation. This is quantified by measuring the hydraulic conductivity or coefficient of permeability. 2.0 TECHNICAL REQUIREMENTS 2.1 The vendor shall provide a CAD drawing of the proposed design. 2.2 The setup should meet the following requirements 2.2.1 It shall comply with accepted testing standards for soil permeability measurements as given by ASTM D5856-95 or ASTM 5084-10. 2.2.2 It shall incorporate a method to control the hydraulic head for testing 2.2.3 It shall include sensors and a data logger for recording of the test data 2.2.4 It shall have an interchangeable permeameter ring that holds the test sample and sealed via gaskets at the top and bottom with clamped plates. 2.2.5 The setup shall use automated controls integrated to the data logger with a touch screen user interface. 2.3 The vendor shall provide three permeameter or test sample chambers as follows 2.3.1 The first permeameter shall contain a soil sample, compacted and shown to have hydraulic conductivity of less than 1x10-7 cm/sec 2.3.2 The second permeameter shall contain a fully cured conductive concrete using Conducrete®. 2.3.3 The third permeameter shall contain a soil compacted and measured to have a hydraulic conductivity of less than 1x10-7 cm/sec, a hole drilled through and filled with Conducrete®. 2.3.4 The permeameter shall be a minimal of 20" in diameter, have a height of >4" 2.3.5 The inner side walls of all three permeameter rings shall be coated with a thin layer of sodium bentonite paste to minimize side-wall leakage. 2.4 The sensors, data acquisition, and controller interface shall include as a minimal 2.4.1 Pressure transducers 2.4.2 Flow Measurement system 2.4.3 Data acquisition and monitoring 2 2.4.4 Temperature measurement and control to ±3°C 2.4.5 A compact touch screen interface to run the experiment automatically, and to display the measurements in real time. 2.4.6 Data Acquisition will use a web browser interface to allow compatibility with windows, iOS, and android operating systems. 2.5 The vendor shall supply all materials and hardware sufficient to perform the permeability measurement to include: 2.5.1 Hydraulic pump to provide required head pressures 2.5.2 Data Acquisition hardware and screen interface 2.5.3 All necessary sensors to enable performance of ASTM D5856 or ASTM 5084 testing, which will include temperature, pressure, and flow sensors. 2.5.4 Data Acquisition storage capacity of at least 32Gb 2.5.5 Soil, Conducrete®, and EnvirAnode® for testing. 3.0 GOVERNMENT FURNISHED MATERIAL (GFM) None 4.0 TRAVEL Travel and associated travel costs should be included in total cost to government. 5.0 OTHER 5.1 Security Personnel performing on this task do not require a security clearance. 5.2 Place of Performance 5.2.1 Fabrication will take place at the contractor site. 5.3 Deliverables 5.3.1 A functioning test setup which is compatible with ASTM D5856 or ASTM 5084 standards for testing of hydraulic conductivity. 5.3.2 A Data Acquisition system to include hardware and functioning codes to allow performance of the hydraulic conductivity measurements.
Award Overview
Award Number
N00244-12-P-1358
Award Amount (SAM.gov award notice)
$32.8K
Award Date
Sep 27, 2012
Awardee
Original Solicitation
Notice ID: 917d546a3f89dcf6fea09dea25e49b9b
Posted Date: Sep 27, 2012
Original Response Deadline: Not specified
Contract Details
No FPDS record matches this award number at the same department yet
Contract details typically appear within 2-4 weeks after award; DoD awards are published about 90 days after signature.
Contacts
Contracting Officer
Primary Contact
Michael Kutner Use this email to contact the Contract Specialist
Documents
No documents available.
Lifecycle
Solicitation:
N0024412T0300- Combined Synopsis
- Awarded
This opportunity has been awarded.
- 2×Combined SynopsisSep 6, 2012
A--Hydraulic Conductivity Test Setup
- AwardedCurrentSep 27, 2012
A--Hydraulic Conductivity Test Setup
Similar Opportunities
Title | Match | Phase | Deadline |
|---|---|---|---|
Additional Details
Solicitation Number
N0024412T0300
Archive Date
Oct 12, 2012