Notice ID: 6f1e4d682541b7d572082233fecee03fAward NoticeAwarded
14--8-Phase Custom Stepper Motor
Awarded on September 17, 2008. Full description on SAM.gov.
Awarded tounder N6893608C0086 (source: SAM.gov award notice)• $495.0K
Overview
- Posted
- September 29, 2008
- Notice type
- Award Notice
- Agency
- Department of WarDepartment of the Navy
Notice details
- Office
- NAVAL AIR WARFARE CENTER
- PSC
- 14: GUIDED MISSLES
- Last updated
- Sep 25, 2026
- Award date
- Sep 17, 2008
- Award amount (SAM.gov award notice)
- $495.0K
Identifiers
- Solicitation number
- N6893608R0069
- Notice ID
- 6f1e4d682541b7d572082233fecee03f
- Award number (PIID)
- N6893608C0086
Description
The Naval Air Warfare Center Weapons Division (NAWCWD) China Lake, CA intends to enter into negotiations for a Firm Fixed Price (FFP) contract on an other than full and open competition basis with The Motion Group 5577 Perrin RD, Clovis, CA 93619-9528. The stepper motor is an eight phase,fast response, fine resolution, digital actuator. General requirements include but are not limited to: 1) Electrical requirements: 1.1) the nominal resistance of each phase is 9 OHMS and is operated with 4 phases on and 4 phases off.; 1.2) Rating without heat sink or fan. The HDM-165-2000-B motor is rated at .75 amps per phase (3 amps total), 10 volts (30 watts) in a 40"C environment. The motor case temperature should not exceed 65 C. 2) Mechanical Requirements: the motor's full step resolution is 2000 steps/revolution with a step size of .18 degrees; 2.1) Nominal Specifications: Accuracy (nonaccumulative +/- 3.5 Arc Minutes, Holding Torque 25 in lbs, rotation Bidirectional, torsional stiffness 3300 in.lb/rad, equivalent rotor inertia .72 lb. In.2, Shaft Radial deflection (1 in. from face) 163 lbs, Shaft Radial Deflection (1 in. from face) 6600 lbs/in, Shaft thrust load max 185 lbs.; 3) Environmental conditions: 3.1) the operating temperature range shall be minimum of 0" centigrade maximum of +55" centigrade. 4) Physical requirements: 4.1) the rabbet is to be concentric to shaft within .002 total indicated runout (TIR); 4.2) The mounting face is to be perpendicular to shaft within .003; . 4.3) The maximum shaft runout shall be .002 TIR measured .12 from face; 4.4) the stepping motor is pre-lubricated and sealed at assembly and requires no additional lubrication; 4.5) the motor shall be supplied with an ITT Cannon type DE-9P connection at the end of flying leads. A mating type DE-9S connector shall be supplied. The connectors will be mechanically secured by means of sliding retainer. Any firm believing that they can provide the 8 Phase stepper motors may submit a written response to be received by the Contract Specialist no later than 15 days after the date of publication of this notice. The solicitation with a detailed list of requirements will be posted on the Navy Electronic Commerce Online Website at http://www.neco.navy.mil and the FEBBIZOPPS website at http://vsearch2.eps.gov/servlet/searchservlet on or about 8/12/08. The solicitation will close on or about 9/12/08. All responsible sources must be registered in the Central Contractor Registration (CCR) database at the following website: https://www.ccr.dlis.mil/ccr/scripts/index.html. All responsible sources may submit a quotation that will be considered by the agency. Responses must include all information requested in the written Request for Proposal (RFP). Evaluation for the award will consider Past performance, price and other factors including technical capability. All responses shall be submitted in writing to the Naval Air Warfare Center Weapons Division Code 210000D, Attn: Gayle Cline, 429 E. Bowen Road, Stop 4015, China Lake, CA 93555-76108 or FAX (760) 939-3095 or, e-mailNAICS Code = 335313 Place of Performance = N/A See Note 22
Award Overview
Award Number
N6893608C0086
Award Amount (SAM.gov award notice)
$495.0K
Award Date
Sep 17, 2008
Awardee
Original Solicitation
Notice ID: 6f1e4d682541b7d572082233fecee03f
Posted Date: Sep 29, 2008
Original Response Deadline: Not specified
Contacts
Contracting Officer
Primary Contact
Gayle Cline (760) 939-8109 Gayle Cline
Documents
No documents available.
Lifecycle
Solicitation:
N6893608R0069- Pre-Solicitation
- Solicitation
- Awarded
This opportunity has been awarded.
- Pre-SolicitationJul 28, 2008
61--8-Phase custom stepper motor
- SolicitationAug 13, 2008
61--8-Phase custom stepper motor
- AwardedCurrentSep 29, 2008
14--8-Phase Custom Stepper Motor
Similar Opportunities
Title | Match | Phase | Deadline |
|---|---|---|---|
Additional Details
Solicitation Number
N6893608R0069
Archive Date
Aug 12, 2009
Office Address
CHINA LAKE, CA, 93555-6018