TECHNOLOGY LICENSING OPPORTUNITY: Compact Modular Furnace
Responses closed . Full description on SAM.gov.
Overview
- Response deadline
- 5:00 PM MDT
- Posted
- April 30, 2026
- Notice type
- Special Notice
- Set-aside
- No Set aside used
- NAICS
- 334516: Analytical Laboratory Instrument Manufacturing
- Agency
- Department of Energy
Notice details
- Office
- TRIAD - DOE CONTRACTOR
- Place of performance
- Los Alamos, New Mexico, 87545
- Last updated
- Oct 28, 2026
- First published
- Last updated on SAM.gov
Identifiers
- Solicitation number
- S-195784
- Notice ID
- 3d6184c4385e4dab808079314b09485b
Description
The Compact Modular Furnace from Los Alamos National Laboratory gives researchers a practical way to perform extreme-temperature testing of molten salts and metals in a glovebox-compatible, tightly controlled environment. By combining a small footprint, interchangeable components, optical access, and the ability to isolate heat directly at the sample, it enables safer and more flexible experiments that would normally require much larger, more expensive equipment. The furnace design supports rapid setup for a range of materials studies, including contact angle measurement, compatibility testing, and thermal cycling, while helping teams work with highly reactive substances without exposing them to air or moisture. The result is a versatile platform that expands what can be studied, shortens experimental turnaround, and brings high-performance thermal testing into a form that is easier to deploy and use. The furnace can be heated using resistive heating elements to reach up to 750°C in vacuum or inductive heating elements to melt high temperature samples such as refractory metals.
The Challenge:
This invention addresses the difficulty of studying highly reactive materials under extreme heat while keeping them isolated from air and moisture. The Compact Modular Furnace provides a way to run controlled experiments on molten salts and metals in a compact setup that can fit inside a glovebox, which is important because these materials can be unsafe or unusable in ordinary open-air equipment. The furnace system can be isolated from the glovebox atmosphere to allow introduction of process gases, high vacuum, or to prevent fumes from contaminating the glovebox environment. It also allows researchers to observe the sample during testing, so they can measure behavior such as wetting, compatibility and thermal response without interrupting the experiment or exposing the material to the environment. By combining a small footprint, adaptable parts and a design that concentrates heat where it is needed, the system reduces the need for large, specialized furnaces and makes advanced testing more practical, flexible, and efficient.
Problems Solved:
The Compact Modular Furnace solves the problem of having to choose between precise high-temperature testing and a controlled, contamination-free environment. It gives researchers a way to heat and observe sensitive materials without exposing them to air, moisture, or other conditions that can distort results or damage the sample. It also addresses the limitations of large, inflexible furnaces by offering a smaller, easier-to-configure setup that can be adapted for different experiments and measurement tools. Protecting sensitive equipment such as cameras and spectrometers from extreme heat conditions. In practice, that means scientists can study molten salts and metals more safely, with less equipment costs, and with better access to the kinds of measurements needed to understand how these materials behave under extreme conditions.
Key Advantages:
- Small enough to fit in constrained lab setups, including gloveboxes
- Helps protect sensitive materials from air and moisture
- Allows researchers observe samples while they are being heated
- Flexible enough to support different kinds of experiments
- Can reduce the need for multiple separate instruments
- May lower setup cost compared with larger, specialized systems
Market Applications:
- Nuclear Energy (materials testing, reactor component development, heat-resistant systems)
- Fusion Energy (high-temperature materials screening, containment studies, component durability)
- Solar Energy (thermal materials evaluation, coatings testing, high-heat performance studies)
- Advanced Materials Research (compatibility testing, wetting behavior, extreme-environment studies)
- Laboratory Instrumentation (specialized testing setups, environmental control systems, sample observation tools)
- Industrial R&D (rapid prototyping, thermal cycling, materials qualification)
Development Status: TRL 5
U.S. Patent pending
LA-UR-26-23234
LANL Tech Partnerships: Unlock the Innovative Potential
Los Alamos National Laboratory offers a wide range of cutting-edge technologies and capabilities that may provide your company with a competitive edge in the market and unlock the innovative potential that can enhance, refine, and revolutionize your products.
LANL’s licensing program focuses on moving inventions developed by our researchers to commercial innovations. Patented and patent pending inventions and copyrighted software are available to existing and start-up companies through exclusive and non-exclusive licensing agreements. For specific discussions, please contact licensing@lanl.gov.
Note: This is not a call for external services for the development of this technology.
https://www.lanl.gov/engage/collaboration/feynman-center/partner-with-us/licensing-technology
m.lanl.gov/tech-search
Award Overview
No prior contract identified
No prior award matched this notice's agency, NAICS, place of performance and PSC within 18 months. It may be a new requirement.
Contacts
Contracting Officer
Primary Contact
Secondary Contact
Documents
No documents available.
Lifecycle
- 1Version 1Special NoticeCurrent
TECHNOLOGY LICENSING OPPORTUNITY: Compact Modular Furnace
Similar Opportunities
Title | Match | Phase | Deadline |
|---|---|---|---|
Non-Invasive Ultrasonic Coating Evaluation for Electrochemical Systems Makers of fuel cells, electrolyzers and other electrochemical devices depend on catalyst coatings applied with tight consistency; yet, today’s inspection tools force production to pause so samples can be pulled and studied in a laboratory. SonicCoat, developed by researchers at Los Alamos National Laboratory, offers a faster path: A gentle ultrasonic probe reads how much catalyst has been laid down while the coating line keeps running, giving producers real-time confidence in every layer without slowing throughput or harming the part. The payoff is higher yield, more uniform device performance and lower material cost across a platform that reaches from clean-energy hardware to batteries, solar films and semiconductors. How it Works The SonicCoat method rests on a simple physical fact: Sound travels through an object differently as the object’s makeup changes. A small transducer sends acoustic waves through a coated part and listens for the natural tones, or resonances, that the material rings back. As the catalyst is sprayed onto the surface layer by layer, those resonant tones shift in pitch and loudness in step with how much material has been added, so the acoustic signature becomes a fingerprint of coating thickness and uniformity. Because the reading is taken by sound rather than by scraping, cutting or exposing the part to X-rays, the inspection happens in place and in seconds, and the part continues down the line unharmed. Technology Description SonicCoat applies Acoustic Resonance Spectroscopy (ARS) to the quality control of catalyst-coated gas diffusion layers, the porous electrodes at the heart of fuel cells and electrolyzers. A coated sample is held in fixturing fitted with transducers that excite it across a broad frequency band and record its resonant response, first as a baseline on the bare substrate and then after each successive catalyst layer. Comparing each response against the baseline reveals how the resonance peaks migrate and change in amplitude, and those movements track the amount of platinum catalyst deposited. Testing has shown peaks moving roughly in proportion to added catalyst content, which demonstrates enough sensitivity to distinguish layer-by-layer differences in loading. Because the measurement is non-destructive and adds little time to the coating cycle, the approach fits directly into continuous production rather than diverting samples for laboratory analysis by scanning electron microscopy, energy dispersive X-ray spectroscopy or X-ray fluorescence, the after-the-fact methods relied on today. Catalyst loading is a primary driver of both cost and performance in electrochemical devices, so verified, consistent deposition translates into steadier power output, longer service life and less wasted precious metal. The same principle extends to any process where a thin coating must be monitored on a substrate, and the technique suits scale-up because it neither caps throughput nor limits the number of parts that can be checked. Advantages Inspects coatings in place while the line keeps moving, with no need to stop and pull samples Fully non-destructive, so parts are never cut, scraped or exposed to X-rays Reads catalyst buildup layer by layer for tight, repeatable quality control Relies on simple, low-cost ultrasonic hardware instead of large laboratory instruments Protects costly materials such as platinum by catching over-coating or under-coating early Scales to high-volume production without limiting output Market Applications Fuel Cell and Electrolyzer Manufacturing Battery Manufacturing Solar Energy Semiconductor Fabrication Protective Coatings TRL 4 U.S. Patent pending LA-UR-26-28073 LANL Tech Partnerships: Unlock the Innovative Potential Los Alamos National Laboratory offers a wide range of cutting-edge technologies and capabilities that may provide your company with a competitive edge in the market and unlock the innovative potential that can enhance, refine, and revolutionize your products. LANL’s licensing program focuses on moving inventions developed by our researchers to commercial innovations. Patented and patent pending inventions and copyrighted software are available to existing and start-up companies through exclusive and non-exclusive licensing agreements. For specific discussions, please contact licensing@lanl.gov. Note: This is not a call for external services for the development of this technology. https://www.lanl.gov/engage/collaboration/feynman-center/partner-with-us/licensing-technology m.lanl.gov/tech-search | 74% | Special Notice | 12/11/2026 |
Entangled Photon Quantum FTIR BroadQ introduces a new way to gather infrared information by using entangled photons without the need of conventional thermal detectors. Developed by scientists at Los Alamos National Laboratory, the platform combines broadband entangled photon generation with a dual-mode imaging layout, creating a path toward compact infrared spectroscopy and microscopy that can operate at very low light levels, avoid cryogenic cooling and support both near-field and far-field measurements from one setup. That combination makes BroadQ attractive for sensitive samples, portable field instruments and advanced imaging workflows where conventional FTIR systems face practical limits. How it Works BroadQ Entangled Photon Quantum FTIR scans a pump beam across entangled photon sources containing spatially varying regions that produce entanglement across different spectral bands, then uses descan optics to combine the output into a stationary broadband beam. Reflective parabolic optics and scan/descan mirror pairs help preserve image quality while avoiding chromatic dispersion, which would otherwise weaken performance across such a wide spectral range. The resulting entangled photons can be the input for an imaging system that supports either near-field or far-field operation without rebuilding or reconfiguring the instrument, which gives the platform flexibility for different spectroscopy and microscopy needs. Technical Description The core innovation is a source of broadband entangled photons. Rather than relying on a single narrowband entangled source, the BroadQ Entangled Photon Quantum FTIR platform scans across structured regions in a source and merges the emitted output into one beam, extending spectral coverage across the near- to mid-infrared range. The approach is source-agnostic, so it can work with nonlinear crystals, meta-surfaces or liquid crystals. A second layer of BroadQ is the imaging architecture. The optical layout places the source at an imaging plane and then relay images or collimates the beam so the same setup can support both near-field and far-field imaging. That matters because near-field imaging can resolve smaller features than far-field methods, while far-field arrangements remain useful for readout of larger fields of view. The disclosed system is intended to make quantum FTIR and related quantum imaging workflows more practical by pairing broadband entangled light with an instrument layout that is easier to use and more adaptable than current approaches. Advantages Broadband infrared coverage from a single platform No need for cryogenic MCT detectors Supports both near-field and far-field imaging without reconfiguration Works at very low light levels, reducing sample damage risk Compatible with multiple entangled photon source types More portable and integration-friendly than conventional FTIR setups Market Applications Analytical Instrumentation (FTIR microscopes, spectroscopy systems) Life Sciences (light-sensitive biological samples, cellular imaging, plant imaging) Chemical Sensing (material identification, spectral analysis) Defense and Security (trace detection, threat reconnaissance) Semiconductor and Materials Characterization (thin films, advanced materials) Remote Sensing (field-deployable infrared analysis) TRL 3 US Patent pending LA-UR-26-23629 LANL Tech Partnerships: Unlock the Innovative Potential Los Alamos National Laboratory offers a wide range of cutting-edge technologies and capabilities that may provide your company with a competitive edge in the market and unlock the innovative potential that can enhance, refine, and revolutionize your products. LANL’s licensing program focuses on moving inventions developed by our researchers to commercial innovations. Patented and patent pending inventions and copyrighted software are available to existing and start-up companies through exclusive and non-exclusive licensing agreements. For specific discussions, please contact licensing@lanl.gov. Note: This is not a call for external services for the development of this technology. https://www.lanl.gov/engage/collaboration/feynman-center/partner-with-us/licensing-technology m.lanl.gov/tech-search | 74% | Special Notice | 06/06/2026 |
This invention by scientists at Los Alamos National Laboratory (LANL) introduces a new type of real-time hydrogen fuel contamination detector that can sense tiny amounts of harmful contaminants before they reach a fuel-cell vehicle. It works by using a special membrane that keeps itself properly hydrated using an internal water reservoir, allowing it to stay sensitive even when measuring completely dry hydrogen—a major challenge for existing sensors. Even small amounts of impurities can permanently damage a fuel-cell car’s power system, and today’s testing methods are slow, expensive, and often done only after problems occur. By enabling continuous, in-line monitoring at hydrogen fueling stations, this technology helps ensure that hydrogen is clean and safe, supporting the growth of a reliable and consumer-friendly hydrogen economy. The Challenge: As hydrogen becomes a mainstream clean fuel, even tiny impurities—like CO, H₂S, or excess moisture—can permanently damage the sensitive fuel-cell systems that power vehicles and equipment. Yet today, hydrogen quality is typically verified using expensive, lab-based instruments that require expert operators and provide results only after the fact. This delay means a single contaminated batch can affect many vehicles before anyone realizes there’s a problem. Traditional sensor concepts have failed because they require adding moisture to the hydrogen stream, which interferes with detecting water contamination and violates emerging fuel standards. The industry needs a simple, real-time, in-line quality monitor that works with dry hydrogen and can be deployed directly at fueling stations. The Solution: The electrochemical Hydrogen Contamination Detector (HCD) is a low-cost device based on the very same materials and components that make up PEM fuel cells. It uses an ultra-low Pt-loaded sense electrode that is similar to a fuel cell electrode but hypersensitized to impurities by virtue of the greatly reduced catalyst loading. Impurities that bind to Pt catalysts inside the fuel cell and interfere with hydrogen absorption and dissociation will behave the same way to the low Pt-loaded HCD working electrode. The low loading makes the HCD even more susceptible to the effects of trace levels of high-impact impurities. The HCD can work in completely dry hydrogen because of LANL’s patented internal water reservoir and wicking mechanism. It can function at much higher sampling pressures than commercial analyzers because it is constructed with off-the-shelf single cell hardware that can easily handle pressures up to 250psi. The HCD approach applies a voltage to electrochemically pump hydrogen gas through the HCD while sampling the dry hydrogen stream to be analyzed for fuel quality. If contaminants are present, the measured hydrogen pumping current will decrease. At well-defined intervals, a high voltage pulse is applied to electrochemically “clean” the ultra-low loaded Pt electrode that “resets” the HCD continuously. The HCD not only detects the impurity but also can track the impurity level in the sample gas as it rises and falls over time. By comparing the response to a certified ultra-high purity “zero-gas” hydrogen source and prior calibration with span gases, the station operator will be immediately informed if the hydrogen to be sold is contaminated and at near real time. In the many baseline experiments performed over 18 months of testing, the HCD has a stable average baseline current demonstrating the efficacy of the approach. Key Advantages: True real-time monitoring: Detects contamination instantly for the 3 most severe fuel cell stack contaminants and does so before it reaches vehicles or equipment. Works with dry hydrogen: Eliminates the need to humidify the gas stream, enabling accurate measurement of all impurities—including water. Compatible with fueling infrastructure: Uses proven PEM fuel-cell components and can be installed directly in high-pressure hydrogen delivery lines. Protects fuel-cell investments: Prevents costly damage to fuel-cell stacks by catching impurities early. Enables the hydrogen economy: Provides the reliability and safety assurance required for widespread adoption of hydrogen vehicles and refueling stations. Market Applications: Hydrogen Production & Distribution Future concepts for Geological Storage of Hydrogen and Co-mingling of Fuels (e.g., hydrogen and methane/natural gas) Fueling Infrastructure Fuel-Cell Vehicle & Equipment Manufacturers Industrial Hydrogen Users Backup Power & Energy Systems Testing, Certification & Safety Organizations Development Status: TRL 6 US Patent No. 10,490,833 B1 LA-UR-25-32317 LANL Tech Partnerships: Unlock the Innovative Potential Los Alamos National Laboratory offers a wide range of cutting-edge technologies and capabilities that may provide your company with a competitive edge in the market and unlock the innovative potential that can enhance, refine, and revolutionize your products. LANL’s licensing program focuses on moving inventions developed by our researchers to commercial innovations. Patented and patent pending inventions and copyrighted software are available to existing and start-up companies through exclusive and non-exclusive licensing agreements. For specific discussions, please contact licensing@lanl.gov. Note: This is not a call for external services for the development of this technology. https://www.lanl.gov/engage/collaboration/feynman-center/partner-with-us/licensing-technology https://www.lanl.gov/engage/collaboration/feynman-center/tech-and-capability-search | 71% | Special Notice | 02/12/2026 |
The UltraGraph Membrane Extraction System from Los Alamos National Laboratory is a compact, modular device that separates and recovers targeted materials from liquid mixtures using an ultra-thin graphene membrane. The system achieves mass transfer performance comparable to conventional separation equipment with active areas 250 times larger. Its building-block design, chemically stable materials and compatibility with standard laboratory fittings allow it to serve a wide range of applications in chemical separations, recovery purifications and biological sample preparation. Organizations can integrate the UltraGraph system into existing laboratory infrastructure with minimal modification, reducing the cost and complexity of adoption. How it Works The UltraGraph system flows two different liquids through separate microchannels etched into quartz substrates, with a three-layer membrane positioned between them. The membrane consists of a monolayer sheet of graphene held between two porous formvar polymer films, each approximately 125 nanometers thick. The formvar layers are permeable, allowing liquid to reach the graphene surface, while the graphene itself blocks the bulk fluids but permits selected ions or particles to transfer across. Liquids can run co-currently or counter-currently depending on the separation task, enabling controlled mass transfer, ion exchange or heat exchange without the two fluids ever mixing. The assembly is secured between steel plates that compress the quartz chips and ETFE gaskets together, forming a leak-resistant seal that connects to standard screw-port fittings. Technical Description The graphene at the center of the membrane is grown via chemical vapor deposition on copper foil and transferred onto formvar support films using a proprietary process that is one to two orders of magnitude faster than conventional PMMA-based transfer methods. The formvar films have tunable porosity ranging from 20% to 60%. At approximately 125 nanometers thick with an elastic modulus of 7.8 GPa, the formvar provides sufficient mechanical support for atomically thin graphene across 100-micrometer-wide channels at flow rates up to 25 microliters per minute. The graphene layer can be functionalized with oxide groups, nanoparticles or engineered pores to adjust selectivity for specific ions or molecules. The total membrane thickness is approximately 250 nanometers, which is orders of magnitude thinner than membranes used in conventional microfluidic separation devices. The quartz microchannel substrates can be configured in patterns ranging from single channels to branching multi-channel networks and radially extending circular designs. In laboratory testing, the system achieved a pH change of approximately 4 in deionized water contacted with an organic triethylamine solution across the graphene membrane, matching the output of a commercial system whose mass transfer area was 250 times larger. The four-channel counter-current configuration demonstrated 17.4% triethylamine transfer at 15 microliters per minute, on par with that commercial benchmark. The modular stacking design allows additional substrate-membrane pairs to be layered to increase throughput without redesigning the housing, and scaling estimates project that a cylindrical multi-layer assembly could process 26 milliliters per minute across more than 1,000 channels. Because the quartz chips are reusable and the membrane materials are inexpensive to produce, the system lowers the economic discard limit for recoverable materials that might otherwise be classified as waste. Advantages High efficiency in a compact form factor — performs comparably to systems with separation areas 250 times larger Tunable selectivity — the graphene membrane can be chemically modified to target specific ions, molecules or particles Modular and scalable — additional chip-and-membrane layers can be stacked to increase capacity without a full redesign Chemically stable and radiation resistant — formvar support layers are inert to most chemicals and tolerate radiation exposure, suiting the system to demanding operating environments Low-cost and reusable components — quartz chips can be reused, membranes are inexpensive to manufacture and standard connectors simplify integration Leak-resistant design — ETFE gaskets and a compression housing address the leakage issues common in prior microfluidic membrane systems Market Applications Water Treatment and Desalination (ion removal, brine processing, contaminant filtration) Pharmaceutical and Biotechnology (drug compound purification, sample preparation, protein separation) Chemical Manufacturing (solvent extraction, chemical purification, catalyst recovery) Environmental Remediation (industrial wastewater treatment, heavy metal removal, pollution control) Medical Diagnostics and Research (blood and plasma separation, point-of-care sample processing, analytical chemistry) TRL 4 LA-UR-26-24077 US Patent No. 11,471,838 LANL Tech Partnerships: Unlock the Innovative Potential Los Alamos National Laboratory offers a wide range of cutting-edge technologies and capabilities that may provide your company with a competitive edge in the market and unlock the innovative potential that can enhance, refine, and revolutionize your products. LANL’s licensing program focuses on moving inventions developed by our researchers to commercial innovations. Patented and patent pending inventions and copyrighted software are available to existing and start-up companies through exclusive and non-exclusive licensing agreements. For specific discussions, please contact licensing@lanl.gov. Note: This is not a call for external services for the development of this technology. https://www.lanl.gov/engage/collaboration/feynman-center/partner-with-us/licensing-technology m.lanl.gov/tech-search | 69% | Special Notice | 09/30/2026 |
When water turns murky or dense with mud, sediment or chemistry, optical cameras stop being useful, and operators are left guessing about what lies on the other side of the fluid. The Acoustic Camera from Los Alamos National Laboratory replaces that guesswork with sharp 3D imagery generated from sound, achieving sub-millimeter depth resolution in near real time. Instead of inferring the size and orientation of a submerged object from an impression block or a low-frequency sonar return, an operator receives an actual shape, with depth cues and material hints, on the first pass. The result is faster decisions in environments that have historically been opaque, whether the goal is recovering a lost tool from a wellbore, checking the integrity of a net pen in a turbid fjord, or inspecting submerged infrastructure where flushing or cleaning the surrounding fluid is not an option. How it Works: The system operates by transmitting high-frequency ultrasonic pulses—typically in the hundreds of kilohertz range (approximately 100–800 kHz)—into the wellbore toward an object of interest. These sound waves reflect off the object and are captured by a two-dimensional acoustic receiver array. By measuring the time-of-flight and spatial distribution of the returned echoes, onboard digital signal processing reconstructs a detailed 3D image of the object in near real time. Because ultrasound propagates through drilling mud and other optically opaque fluids, the system can generate clear 3D images without requiring fluid replacement or well cleanout. Technical Description: Acoustic Camera uses a broadband piezoelectric transducer to insonify the object with frequencies between roughly 100 kHz and 800 kHz. Because attenuation in fluids scales with the square of frequency, this band is chosen as the practical compromise between mud penetration (favoring lower frequencies) and image resolution (favoring higher frequencies). Reflected pulses pass through a compound high-density polyethylene (HDPE) acoustic lens consisting of a fixed plano-concave primary element and a motor-positioned secondary element, allowing focus adjustment without changing the receiver position, and yielding an appropriate magnification factor. The receive array is a 2D segmented piezoelectric detector submerged in sound-communicating fluid whose low sound speed provides a roughly three-fold reduction in wavelength versus water and enables a compact camera housing. Image reconstruction can use either tone-burst excitation with first-arrival extraction or, for higher resolution, frequency-chirp excitation followed by cross-correlation of the transmit and receive signals — yielding depth resolution below 1 mm at working distances of up to approximately 2 feet in drilling mud. The film allows the source and detector to share a single optical axis, eliminating the multiple reflections and aberrations introduced by semi-transparent acoustic mirrors used in earlier architectures. Key Advantages: Imaging through opaque fluids: Enables 3D visualization in drilling mud and other optically opaque, acoustically attenuating fluids where optical systems fail Reduced cost and downtime: Eliminates the need for well cleanout and accelerates diagnostic decision-making during fishing operations Higher-quality diagnostics: Provides accurate 3D information on object shape and orientation, surpassing mechanical impression methods Lower operational risk: Improves fishing-tool selection and reduces the likelihood of failed recovery attempts or well loss Extensible platform: Applicable to other downhole and industrial environments involving optically opaque fluids, supporting future product expansion Market Applications: Oil & Gas Mining and Geotechnical Operations Enhanced Geothermal Systems Industrial Inspection and Maintenance Energy and Utilities Infrastructure Government and Defense Development Status: TRL 4 US Patent No. 10,054,676-B2 LA-UR-26-24351 LANL Tech Partnerships: Unlock the Innovative Potential Los Alamos National Laboratory offers a wide range of cutting-edge technologies and capabilities that may provide your company with a competitive edge in the market and unlock the innovative potential that can enhance, refine, and revolutionize your products. LANL’s licensing program focuses on moving inventions developed by our researchers to commercial innovations. Patented and patent pending inventions and copyrighted software are available to existing and start-up companies through exclusive and non-exclusive licensing agreements. For specific discussions, please contact licensing@lanl.gov. Note: This is not a call for external services for the development of this technology. https://www.lanl.gov/engage/collaboration/feynman-center/partner-with-us/licensing-technology m.lanl.gov/tech-search | 68% | Special Notice | 06/30/2026 |
Additional Details
Solicitation Number
S-195784
Archive Date
May 18, 2027
Office Address
Columbus, OH, 43201