GovChime
Notice ID: 7cdd0a03f7589445af828fec5a9c3ec6Award NoticeAwarded

Probe Cards

Awarded on September 28, 2012. Full description on SAM.gov.

Awarded tounder SB1341-12-SU-1648 (source: SAM.gov award notice)• $222.8K

Overview

Posted
October 1, 2012
Notice type
Award Notice
NAICS
334515: Instrument Manufacturing for Measuring and Testing Electricity and Electrical Signals
Agency
Department of CommerceNATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY

Notice details

Office
DEPT OF COMMERCE NIST
Place of performance
NIST, Gaithersburg, 20899
PSC
66: INSTRUMENTS AND LABORATORY EQPT
Last updated
Dec 5, 2025
Award date
Sep 28, 2012
Award amount (SAM.gov award notice)
$222.8K

Identifiers

Solicitation number
SB1341-12-RP-0100
Notice ID
7cdd0a03f7589445af828fec5a9c3ec6
Award number (PIID)
SB1341-12-SU-1648

Description

The purpose of this amendment is to respond to questions from industry. As a result, the RFP is amended as follows: 1. The RFP requires a 4 um tip diameter. Is there any flexibility for the Government to accept a larger tip diameter? The specification for probe tip radius is for the sharpness of the tip in the case that the tip is sharpened at the very end. For probes with flat tip, the diameter can be as large as 8 microns in diameter. 2. Do you have a specification for planarity? The Government does not specify planarity and the offerors may propose based on their design as long as all other specifications are met. 3. Do you have a specification for overdrive? 50 um overdrive is acceptable. The key concern is the size of the scrub mark at maximum overdrive. It shall be kept below 15 um. 4. Do you have a specification for alignment? +/- 6 um maximum for alignment is acceptable. 5. Do you have a specification for contact force? Contact force is dependent upon the tip size. Since the contact pad material does vary from soft (Aluminum) to hard (TiN), the contact force must strike a balance. 6. Do you have a specification for tip depth? Tip depth is not critical for the Government - the offeror may propose based on their design as long as all other specifications are met. 7. Will a stiffener be required? Do you want to provide some threaded holes in the heat sink so that we can screw the ring to the heat sink and take the PCB out of the mechanical equation? The offeror may propose based on their design as long as all other specifications are met and it is up to the offeror to decide if a stiffener is needed or not to hold the probes in precise position at 200C (not wafer temperature, which may be significantly higher). If threaded holes are needed in the heat sink, it is possible as long as it is not conflicting with topside optical alignment using microscope. 8. Would the Government accept other than 1 pA per volt? This is a critical specification. 1 pA per volt is preferred, but the Government would accept 10 pA per volt as the maximum. 9. Can you give us some information about the bond pads: Al Thickness and pad type: Low-K; POA; BPOP? The system is designed for a wide range of reliability studies. Thus the bond pad will vary widely. 10. Can you send more mechanical information about how the card will be mounted to the prober? The probe card is mounted onto the Aluminum heat sink by the screw holes as shown on the drawing. The aluminum heat sink is a solid slap (1/2" thick) that is shaped similar to the probe card (with accommodation of mounting and the connecters). This aluminum slap is mounted on an Aluminum post (with thermal grease to ensure good thermal conduction to the post) that is connected to a water-cooled base plate.

Full description on SAM.gov

Award Overview

Award Number

SB1341-12-SU-1648

Award Amount (SAM.gov award notice)

$222.8K

Award Date

Sep 28, 2012

Awardee

Awardee UEI

NB99AMR3CAG8

Original Solicitation

Notice ID: 7cdd0a03f7589445af828fec5a9c3ec6

Posted Date: Oct 1, 2012

Original Response Deadline: Not specified

Contract Details

Contract data not yet available

Contract details typically appear within 2-4 weeks after award; DoD awards are published about 90 days after signature.

Contacts

Contracting Officer

Primary Contact

Documents

No documents available.

Lifecycle

Solicitation:SB1341-12-RP-0100
  1. Combined Synopsis
  2. Awarded

This opportunity has been awarded.

  1. 2×
    Combined SynopsisAug 3, 2012

    Probe Cards

    Notice f991b451b362f2a9aec0d04f6515f150 on SAM.gov

  2. AwardedCurrentOct 1, 2012

    Probe Cards

    Notice 7cdd0a03f7589445af828fec5a9c3ec6 on SAM.gov

Similar Opportunities

Title
Match
Phase
Deadline

Additional Details

Solicitation Number

SB1341-12-RP-0100

Archive Date

Jul 3, 2019