Remove_Replace_Fountains_SantaFeIndianHealthCenter
Overview
- Response deadline
- 12:30 PM MST
- Posted
- December 3, 2025
- Notice type
- Sources Sought
- Set-aside
- Buy Indian Set-Aside (specific to Department of Health and Human Services, Indian Health Services)
- NAICS
- 333248: All Other Industrial Machinery Manufacturing
- Agency
- Department of Health and Human ServicesINDIAN HEALTH SERVICE
Notice details
- Office
- ALBUQUERQUE AREA INDIAN HEALTH SVC
- Place of performance
- Santa Fe, New Mexico, 87505
- Last updated
- Nov 5, 2026
- First published
- Last updated on SAM.gov
Identifiers
- Solicitation number
- SFIHC(Remove_Replace_Water_Fountains)
- Notice ID
- 220559455bb848b58f5c46d87bebb2ea
Description
1. PURPOSE
The Albuquerque Area Indian Health Service (AAIHS), Santa Fe Indian Health Center (SFIHC) has a requirement to remove and replace all existing drinking fountains throughout the Santa Fe Indian Health Center with new Brand Name Elkay ezH2O Enhanced refrigerated, filtered, stainless steel bottle-filling stations. One bi-level ADA model (LZSTL8WSVRSK) will be installed at the main hospital clinic entrance. Twelve single ADA models (LZS8WSVRSK) will be installed in the other designated campus locations identified in the attached floor plan. The contractor shall also furnish three years’ worth of OEM replacement filters for all units (WaterSentry 6000 gal Model 51600C and WaterSentry 3000 gal Model 51300C, as appropriate for each model) for preventive maintenance stock., Santa Fe, New Mexico.
2. APPLICABLE STANDARDS
All work shall comply with the following standards:
- NFPA 70 (National Electrical Code)
- Uniform Plumbing Code (UPC)
- ADA and ICC A117.1 Accessibility Standards
- ASHRAE 18 for cooler capacity performance
- IHS Safety and Infection Control Policy for construction activities
- Manufacturer installation instructions and warranty requirements per Elkay specifications
3. PRODUCTS AND MATERIALS
Equipment
3.1 Bi-Level Unit (1 each): Elkay ezH2O Enhanced Model LZSTL8WSVRSK Filtered Refrigerated Stainless.
-8.0 GPH chilling capacity
-Hands-free sensor-activated bottle filler with LED illumination
-Vandal-resistant bubblers with push bar activation
-Built-in NSF/ANSI 42, 53, 372 & 401 filter system
-ADA compliant bi-level configuration
3.2 Single Units (12 each): Elkay ezH2O Enhanced Model LZS8WSVRSK Filtered Refrigerated Stainless.
-8.0 GPH chilling capacity
-Hands-free sensor activation and visual filter monitor
-Stainless finish with vandal-resistant bubbler
3.3 Filtration System
Filter Model 51600C (WaterSentry 6000 Gal High-Capacity)
- Used in all single-unit installations (LZS8WSVRSK).
- NSF/ANSI 42, 53, 372, and 401 certified for reduction of lead, microplastics, Class 1 particulates, cysts, and chlorine taste/odor.
- Rated for 6,000 gallons or 12 months of service life.
- High-capacity filter minimizes maintenance and replacement frequency in high-traffic areas.
Filter Model 51300C (WaterSentry 3000 Gal Standard-Capacity)
- Used in the bi-level unit installation (LZSTL8WSVRSK).
- NSF/ANSI 42, 53, 372, and 401 certified for the same contaminant reduction performance as the 51600C.
- Rated for 3,000 gallons or 12 months of service life.
- OEM filter supplied with each bi-level unit and compatible with the Elkay ezH2O Versatile Bi-Level ADA Cooler configuration.
Updated Stocking Requirement: In addition to installing filters upon installation, the contractor shall furnish an additional three (3) years’ worth of OEM replacement filters for all installed units—providing the appropriate number of Model 51600C filters for the twelve (12) single-station units and Model 51300C filters for the one (1) bi-level unit—to support preventive maintenance changeouts and facility stock.
4. WORK REQUIREMENTS
4.1 Pre-Installation:
Coordinate with IHS Facilities Maintenance and OEHE staff to confirm all fountain locations on-site.
- Verify electrical and plumbing connections are available and meet manufacturer requirements.
- Submit product data sheets and installation shop drawings for approval before procurement.
4.2 Removal and Disposal: - Disconnect and remove all existing drinking fountains and mounting hardware.
- Cap plumbing and electrical as needed during installation phasing.
- Dispose of all removed fixtures off-site in accordance with local and federal waste management regulations.
- Ensure no disruption to clinical operations and maintain infection control barriers as required by PCRA protocols.
4.3 Installation: - Install new Elkay units per manufacturer’s specifications.
- Verify proper alignment, secure wall mounting, and GFCI-protected electrical connection.
- Test for leaks, drainage function, and cooling performance.
- Program each unit’s LED filter monitor and Green Ticker™ display.
- Provide cleaning and surface sanitization after installation.
Contractor will provide all equipment, tools, and labor to accomplish duties for this project.
4.4 Warranty and Documentation:
- Provide manufacturer’s warranty documentation (5 years on refrigeration system, 1 year on electrical and water systems).
- Deliver as-built installation records showing unit locations and serial numbers.
- Supply filter inventory list with changeout schedule for three years.
5. DELIVERABLES
- 1 bi-level filtered stainless unit installed (Main Hospital Entrance)
- 12 single filtered stainless units installed (various buildings per floor plan)
- 36 replacement filters (51600C and 51300C) provided for preventive maintenance stock
- Removal and off-site disposal of 13 existing fountains
- Operation and maintenance manuals and training for Facilities staff.
6. QUALITY ASSURANCE
All equipment shall be new and factory-tested. Installation work will be subject to inspection by IHS Facilities
Maintenance and OEHE representatives. Contractor must perform final commissioning to verify system
performance and sanitary operation.
7. SCHEDULE
Work shall be completed within 90 days of Notice to Proceed, including removal, installation, testing, and final
acceptance.
8. SAFETY AND INFECTION CONTROL
The contractor shall adhere to IHS PCRA and infection control protocols during all installation activities within clinical
areas. Dust barriers, negative air control, and noise management measures shall be implemented to protect patients
and staff.
HOURS OF OPERATION & PLACE OF DELIVERY:
Hours of operation will be M-F from 8:00 AM to 4:30 PM.
The Contractor shall provide to the following facility:
Santa Fe Indian Health Center
Attn: Nursing Department
1700 Cerrillos Road
Santa Fe, NM 87505
CONTRACTING OFFICER’S RESPRSENTATIVE (COR)/POINT OF CONTACT (POC):
The Contractor shall verify all equipment information and coordinate delivery with the COR/ACOR as follows:
Travis Snyder, travis.snyder@ihs.gov, (505) 946-9209.
Eric Wright, eric.wrignt@ihs.gov (505) 946-9207.
STATEMENT OF OBJECTIVES:
- Locate eligible and qualified Small Business Indian Firms to support IHS procurement needs under NAICS code: 333248 – All Other Industrial Machinery Manufacturing.
- Utilize the information received with future acquisition planning efforts and potential Buy Indian set aside.
HOW TO RESPOND:
This is a sources sought notice under the authority of the Buy Indian Act. The Indian Health Service (IHS) is attempting to locate qualified and eligible Small Business Indian Firms, “Native American Indian Owned and Operated businesses,” that can provide services/supplies to the Indian Health Service. This is a request for information only, this is not a solicitation. Responses to this notice are not considered offers and cannot be accepted by the Government to form a binding contract. Any information submitted by respondents to this notice is strictly voluntary with no obligation or incurred cost by the government.
Provide with response –
- E-mail response. Shall be in a printer friendly format, Word or PDF, 8x11 page size, 5-page limit.
- Certification as a Small Business Indian Firm. The government is ONLY interested in Small Business Indian Firms. (See attached Representative Form).
- The government requests that interested parties respond to this notice if applicable and identify your business status to the identified NAICS code.
- Prospective vendors shall be properly registered in SAM.gov; this includes proper registration as a Small Business Indian Firm and if eligible, registered as applicable small business certifications (e.g. HUBZone, 8(a), Service Disabled Veteran Owned, Veteran Owned, Women-Owned, Small Disadvantaged), in order for IHS to issue an award and claim procurement actions with eligible Small Business Indian Firms.
- Provide detailed capabilities statement, website, and e-catalog as it pertains to 333248 – All Other Industrial Machinery Manufacturing.
- Provide Unique Entity Identifier (UEI) created in SAM.gov registration.
- Identify Business Size: Small Business Indian Firm, Small Businesses or a Large Indian-Owned Firm.
- GSA/FSS contract holders – provide GSA/FSS/VA or other GWAC contract number, only if applicable.
Award Overview
No prior contract identified
No prior award matched this notice's agency, NAICS, place of performance and PSC within 18 months. It may be a new requirement.
Contacts
Contracting Officer
Primary Contact
Documents
Files (1)
- Download
BLANK - IHS IEE Representation Form_Jan 2022_508 Compliant.pdf
129 KBAdded in Sources Sought version 3Posted
Lifecycle
- 3Version 3Sources SoughtArchivedCurrent
Remove_Replace_Fountains_SantaFeIndianHealthCenter
Similar Opportunities
Title | Match | Phase | Deadline |
|---|---|---|---|
GasFlow DLP Printing Interface, developed by scientists at Los Alamos National Laboratory, helps resin-based 3D printing systems produce finer details, faster builds and more consistent part quality by controlling oxygen where curing happens most critically. The open-surface approach fits well with bottom-up DLP and related vat photopolymer processes, and it can enhance existing printer designs, as well as new platforms, by improving print fidelity, process stability and material flexibility. How it Works The system adds a second liquid beneath the printable resin inside the vat, creating a stable fluid-fluid interface between the two liquids. This interface is where the resin is polymerized, removing the need to pull the polymerized layer off the surface - an inherent default in the DLP process. The lower liquid is chosen to be an immiscible, high-density fluid, such as a perfluorinated fluid, that is treated with an inert gas and circulated continuously during printing. As it flows beneath the resin and above the transparent vat window, the lower liquid removes oxygen from the resin and introduces inert gas in its place, which reduces oxygen inhibition at the curing zone. With less oxygen interfering with polymerization, projected light can cure smaller features more reliably, more quickly and more uniformly across the part with less bleeding. Technical Description The patented GasFlow DLP Printing Interface is designed for additive manufacturing methods such as DLP, SLA and related photopolymer printing processes. The GasFlow DLP Printing Interface uses a first container or vat with a transparent portion, a first fluid positioned against that transparent portion and a second fluid that serves as the printable resin. The first fluid and second fluid form a fluid-fluid interface, with the first fluid located between the vat window and the resin. A circulation system moves the first fluid through the vat and an associated treatment container by way of conduits and a pumping mechanism. In representative embodiments, the first fluid is a perfluorinated solvent that has been treated with an inert gas such as nitrogen, helium, argon or carbon dioxide. As the treated first fluid circulates, it removes oxygen from resin at the interface and helps replace that oxygen with inert gas, which improves polymerization performance at the print surface. Oxygen in standard resin systems can suppress curing, which means more energy is required than necessary which in turn can create uneven polymerization that leaves parts overcured in some regions and undercured in others making very small features difficult to print. Features below about 50 microns in diameter may fail to print when normal oxygen levels are present. GasFlow DLP Printing demonstrated print speed improvement of at least one-third, with larger gains considered possible under optimized conditions. An added benefit to flowing fluid is that the system can provide temperature-control to help manage heat buildup during printing, which can improve part quality and widen the range of usable resin chemistries. Advantages Produces finer features and higher print resolution Reduces oxygen-related defects during curing Speeds printing compared with standard setups (oxygen exposed) Improves consistency across the part, including edge-to-center uniformity Supports retrofit potential for many bottom-up DLP printers Increases lifetime of liquid resin May enable use of resin chemistries that are otherwise difficult to process because of overheating or curing instability Market Applications Additive Manufacturing (resin 3D printers, printer upgrades, production platforms) Industrial Manufacturing (precision polymer parts, lightweight structures, fabrication tooling) Medical and Dental (custom polymer components, device fabrication, detailed models) Electronics and Microfabrication (fine-feature polymer structures, patterned parts, prototyping) Research and Laboratory Equipment (materials development, process testing, advanced printing systems) Aerospace and Defense (complex geometries, lattice structures, specialty components) TRL 4 US Patent No. 11,911,955 LA-UR-26-29477 LANL Tech Partnerships: Unlock the Innovative Potential Los Alamos National Laboratory offers a wide range of cutting-edge technologies and capabilities that may provide your company with a competitive edge in the market and unlock the innovative potential that can enhance, refine, and revolutionize your products. LANL’s licensing program focuses on moving inventions developed by our researchers to commercial innovations. Patented and patent pending inventions and copyrighted software are available to existing and start-up companies through exclusive and non-exclusive licensing agreements. For specific discussions, please contact licensing@lanl.gov. Note: This is not a call for external services for the development of this technology. https://www.lanl.gov/engage/collaboration/feynman-center/partner-with-us/licensing-technology m.lanl.gov/tech-search | - | Special Notice | 04/06/2027 |
Engineered Porous Print Materials enables manufacturers to produce complex, high-surface-area structures with precisely engineered porosity at macro, micro and nano scales — all from a single printable composition and a standard stereolithography printer. By eliminating the need for secondary coatings, multi-step mold processes or specialized equipment, this technology developed by Los Alamos National Laboratory simplifies the production of advanced porous materials while opening design possibilities that conventional fabrication methods cannot achieve. Organizations seeking to improve the performance of catalytic reactors, filtration systems, thermal management devices, energy storage components or biomedical scaffolds, to name a few, can now access a versatile, low-cost platform that translates digital designs directly into functional, multi-material foam structures with tunable chemistry and architecture. How it Works The process begins with a specially formulated resin that contains three key ingredients mixed together: a polymer precursor that can be hardened by light, a porogenic solvent that induces phase separation during hardening, and a structural precursor (such as a metal salt or ceramic precursor) that will ultimately form the skeleton of the final part. When loaded into a commercial SLA 3D printer, the resin is cured layer by layer using light, producing a printed intermediate structure composed of a nanoporous polymer gel with the structural precursor distributed uniformly throughout. Post-printing processing — which may include controlled heating, chemical reduction or catalytic treatments depending on the target material — converts the structural precursor into the desired solid (metal, ceramic or carbon) while decomposing and removing the polymer gel. The spaces formerly occupied by the polymer gel become a second, finer tier of porosity nested inside the larger pores defined by the printed geometry, and additional processing steps such as de-alloying can introduce a third, nanoscale tier of porosity. The entire workflow uses a single resin formulation with no need to add coatings or secondary materials after printing. Technical Description The printable composition is engineered so that the polymer precursor component (typically an acrylate monomer such as polyethylene glycol diacrylate) undergoes photopolymerization in the presence of a porogenic solvent (such as dimethylformamide or water) that is deliberately chosen for its low compatibility with the resulting polymer network. During curing, the polymer phase-separates from the solvent, creating a sponge-like gel with pore sizes and volumes that can be tuned by adjusting the solvent-to-monomer ratio, solvent chemistry and the inclusion of structure-directing additives. A photoinitiator and a polymerization quenching compound (an absorber dye) are included to control layer thickness and prevent unwanted curing beyond the intended print pattern. The structural precursor — which can be a dissolved metal salt, a pre-ceramic alkoxide, a carbonaceous precursor or a pre-metal oxide — is homogeneously incorporated within the gel phase during printing, enabling an “inside-out” assembly of the final material, or could be absorbed through wicking into the porous, spongelike material before post processing. After printing, downstream thermal and chemical treatments convert the structural precursor into the target material and remove the polymer template. For metal-based products, heating reduces metal ions to colloidal particles within the gel; further sintering fuses those particles into a continuous metallic skeleton while the polymer decomposes, leaving behind a free-standing porous metal replica of the original printed geometry. Isotropic shrinkage during polymer removal can reduce feature sizes well below the printer's native resolution, enabling structural details that conventional SLA cannot achieve on its own. Demonstrated material systems include silver, gold (with trimodal porosity achieved through silver-gold de-alloying), silica, boron carbide, copper, iron and cobalt oxide. Pore diameters span from greater than one millimeter at the macro scale down to below 100 nanometers at the nano scale, and all pore networks remain interconnected and accessible throughout the bulk of the part. Advantages Single-resin workflow instead of multiple coating steps Multi-scale porosity in one printed part Works across several material types Compatible with standard stereolithography equipment Internal pores stay connected and accessible Pore size and density can be adjusted through formulation and processing Market Applications Catalysis (reactor supports, flow-through catalyst bodies) Energy Storage (battery electrodes, capacitor structures) Thermal Management (heat exchangers, heat pipe wicks, cooling components) Filtration and Separations (fluid filters, gas scrubbers, purification media) Biomedical (bone scaffolds, culture substrates) Lightweight Structures (reinforcement, insulation, fire protection parts) U.S. Patent Nos. 11,267,920; 12,054,569; pending LA-UR-26-23577 TRL 4 LANL Tech Partnerships: Unlock the Innovative Potential Los Alamos National Laboratory offers a wide range of cutting-edge technologies and capabilities that may provide your company with a competitive edge in the market and unlock the innovative potential that can enhance, refine, and revolutionize your products. LANL’s licensing program focuses on moving inventions developed by our researchers to commercial innovations. Patented and patent pending inventions and copyrighted software are available to existing and start-up companies through exclusive and non-exclusive licensing agreements. For specific discussions, please contact licensing@lanl.gov. Note: This is not a call for external services for the development of this technology. https://www.lanl.gov/engage/collaboration/feynman-center/partner-with-us/licensing-technology m.lanl.gov/tech-search | - | Special Notice | 06/04/2026 |
This flash sinter-forging technology from Los Alamos National Laboratory enables manufacturers to produce dense, net- or near-net-shape ceramic components in minutes rather than hours or days, while cutting energy consumption by up to 90% and significantly reducing production costs. By simultaneously applying electric current, heat, and mechanical pressure, the process consolidates shaping, densification, and finishing into a single, compact operation, eliminating much of the costly machining typically required for hard, brittle ceramics. The result is faster throughput, lower capital and operating expenses, smaller equipment footprints, and improved sustainability—while also enabling superior microstructural control and access to advanced or difficult-to-sinter materials. How it Works: The technology works by placing ceramic powder into a specially designed die and then applying three inputs at once: an electric field and current, moderate external heating, and mechanical pressure. As electricity passes directly through the ceramic, it rapidly heats the material from the inside, dramatically accelerating the bonding of particles while keeping overall furnace temperatures lower than conventional methods. At the same time, controlled pressure compresses and shapes the material as it densifies, allowing the part to reach high density while already close to its final geometry. Sensors and software coordinate the electrical, thermal, and mechanical conditions in real time, enabling precise control of the process and material behavior. By integrating electrical activation and forging into a single, tightly controlled step, the system achieves fast densification and shaping that would otherwise require multiple, time-intensive processing stages. Key Advantages: Minutes-long processing: Produces dense ceramic parts far faster than conventional sintering methods. Up to ~90% energy reduction: Direct electrical heating dramatically lowers energy use and operating costs. Near-net shaping: Forms parts during densification, greatly reducing or eliminating costly post-machining. Lower total manufacturing cost: Combines forming, sintering, and finishing into a single streamlined step. Advanced material capability: Enables difficult-to-sinter and next-generation ceramics with controlled microstructures. Compact and scalable: Smaller footprint and lower power requirements support deployment from R&D to industrial production. Market Applications: Semiconductor manufacturing (high-purity ceramic components, fixtures, insulators, wear parts) Aerospace and defense (high-temperature components, protective structures, lightweight ceramic parts) Energy and nuclear (fuel cells, solid-state batteries, nuclear and high-temperature energy ceramics) Medical and dental (implants, prosthetics, precision ceramic components) Industrial and manufacturing (wear-resistant parts, tooling components, structural ceramics) Additive and advanced manufacturing (post-processing of 3D-printed ceramic parts, rapid densification of complex shapes) Development Status: TRL 3 US Patent No. 12,465,971 LA-UR-26-23345 LANL Tech Partnerships: Unlock the Innovative Potential Los Alamos National Laboratory offers a wide range of cutting-edge technologies and capabilities that may provide your company with a competitive edge in the market and unlock the innovative potential that can enhance, refine, and revolutionize your products. LANL’s licensing program focuses on moving inventions developed by our researchers to commercial innovations. Patented and patent pending inventions and copyrighted software are available to existing and start-up companies through exclusive and non-exclusive licensing agreements. For specific discussions, please contact licensing@lanl.gov. Note: This is not a call for external services for the development of this technology. https://www.lanl.gov/engage/collaboration/feynman-center/partner-with-us/licensing-technology m.lanl.gov/tech-search | - | Special Notice | 05/11/2026 |
The Indian Health Service, Shiprock Service Unit is issuing this sources-sought notice (SSN) to identify capable Indian-owned, economic enterprises – large (IEE) or small (ISBEE) – that can provide hearing aid fitting and verification with the following minimum requirements: Key Features: • Dual ear capability: Simultaneous measurement of both ears • Comprehensive test suite: Includes speechmap counseling, bone conduction verification, and pediatric probe tube placement with ProbeGuide+ • Flexible setup: Works in clinics, hospitals, and pediatric audiology settings • High accuracy: Frequency accuracy ±1% and measurement accuracy within ±1–4 dB depending on range • Advanced stimuli: Calibrated speech, broadband noise, tone bursts, and user supplied WAV files Technical Specifications: • REM speakers: Dual 5×9 cm with ducted ports. • Frequency range: 200–16,000 Hz. • Dynamic range: 30–135 dB SPL (REM) / 30–140 dB SPL (test box). • Measurement accuracy: ±1 dB at 1 kHz; ±1.5–4 dB depending on frequency. • Display: 12.1 inch LED backlit active color. • Dimensions: Display unit 35.6×40.3×16.5 cm; test box 35.6×13.7×32.8 cm. • Power: 100–240 V, 47–63 Hz, 1.35 A. Copilot Search, October 23, 2026, Audioscan Verifit VF-2 Description, description of 8531954 verifit vf-2 - Search The use of hearing aid fitting and verification is to reduce the risk of hearing aid rejection; avoid costly remakes and ensure patients experience optimal benefit from their devices. Last, provide installation and training for Audiology Department. Other capable firms are also invited to respond to this SSN. The Contracting Officer will consider responses for Buy Indian Act (25 U.S.C. 47) opportunities first, then for set aside programs under the Small Business Act (41 U.S.C. 3104). The applicable North American Industry Classification System (NAICS) code assigned to this requirement is 334510-Hearing aids, electronic, and manufacturing with a small business size standard of 1,250 employees. THIS IS NOT A SOLICITATION. Information collected from this notice is purely for market research only and will be used to determine the contracting office’s acquisition strategy including competition, set asides, and locating Indian-owned economic enterprises. Submission of any information in response to this market survey is purely voluntary. The government assumes no financial responsibility for any costs incurred in response to this request for information. In accordance with FAR 4.203-1(b), offerors and quoters must be registered in System for Award Management at SAM.gov, at the time an offer or quotation is submitted and at time of award. Submission Instructions: Interested parties who consider themselves qualified to perform the above-listed services are invited to submit a response to this notice by November 03, 2026, 4:30 p.m. MST to Karen James, Contract Specialist at karen.james@ihs.gov with the subject line “SSN – SS-SRSU-27-0003. Your submission must include the following information, at a minimum: 1. Company Profile that includes: UEI, Name and Address, Primary POC information, business size and type of ownership, socio-economic status/participation such as 8(a), WOSB/EDWOSB, SDVOSB and HUBZone, identification of Native American ownership, SAM.gov representations and certifications, and other related documentation. 2. A brief statement of the company’s capability that relates to the described government requirement. Additional demonstrations of capability may include current and past performance history for the same or similar requirement, established contracts such as GSA or VA Schedule, etc. 3. Indian-owned Small Business Economic Enterprises (ISBEEs) and Indian-owned Economic Enterprises (IEEs) must also submit a completed IHS IEE Representation Form (attached) in accordance with HHSAR 326.606-1(b). Telephone inquiries will not be accepted or acknowledged, and no feedback or evaluations will be provided to companies regarding their submissions. | - | Market Research | 11/03/2026 |
Sources-Sought Notice The Indian Health Service, Gallup Service Unit is issuing this sources-sought notice (SSN) to identify capable Indian-owned, economic enterprises – large (IEE) or small (ISBEE) – that can deliver and install two *DRAFT* Thermo Scientific TSX3005GA blood bank refrigerators and one *DRAFT* Thermo Scientific TSX5030FA freezer for Gallup Indian Medical Center’s (GIMC) Laboratory department. In addition, the prospective contractor must also: -Level and secure equipment as required by the manufacturer. -Verify electrical compatibility. -Configure temperature setpoints. -Configure audible, visual, and remote alarms. -Verify proper door operation and equipment functionality. -Perform complete equipment startup and commissioning in accordance with the manufacturer's installation and operating instructions. -Operational testing, temperature performance testing, alarm and monitoring verification. -Provide on-site training for GIMC staff. Other capable firms are also invited to respond to this SSN. The Contracting Officer will consider responses for Buy Indian Act (25 U.S.C. 47) opportunities first, then for set aside programs under the Small Business Act (41 U.S.C. 3104). The applicable North American Industry Classification System (NAICS) code assigned to this requirement is 333415- Air-Conditioning and Warm Air Heating Equipment and Commercial and Industrial Refrigeration Equipment Manufacturing with a small business size standard of 1,250 employees. THIS IS NOT A SOLICITATION. Information collected from this notice is purely for market research only and will be used to determine the contracting office’s acquisition strategy including competition, set asides, and locating Indian-owned economic enterprises. Submission of any information in response to this market survey is purely voluntary. The government assumes no financial responsibility for any costs incurred in response to this request for information. In accordance with FAR 4.203-1(b), offerors and quoters must be registered in System for Award Management at SAM.gov, at the time an offer or quotation is submitted and at time of award. Submission Instructions: Interested parties who consider themselves qualified to perform the above-listed services are invited to submit a response to this notice by 11/19/2026 at 10:00AM (MST) to Adam James, Procurement Tech, at Adam.James@ihs.gov with the subject line “SSNGSUT1-20270001.” Your submission must include the following information, at a minimum: Company Profile that includes: UEI, Name and Address, Primary POC information, business size and type of ownership, socio-economic status/participation such as 8(a), WOSB/EDWOSB, SDVOSB and HUBZone, identification of Native American ownership, SAM.gov representations and certifications, and other related documentation. A brief statement of the company’s capability that relates to the described government requirement. Additional demonstration of capability may include current and past performance history for the same or similar requirement, established contracts such as GSA or VA Schedule, etc. Indian-owned Small Business Economic Enterprises (ISBEEs) and Indian-owned Economic Enterprises (IEEs) must also submit a completed IHS IEE Representation Form (attached) in accordance with HHSAR 326.606-1(b). Telephone inquiries will not be accepted or acknowledged, and no feedback or evaluations will be provided to companies regarding their submissions. | - | Market Research | 11/19/2026 |
Additional Details
Solicitation Number
SFIHC(Remove_Replace_Water_Fountains)
Archive Date
Dec 27, 2025
Office Address
ALBUQUERQUE, NM, 87110