GovChime
Notice ID: 056919cf542efd8930b3476c7510da9cSolicitation

23--Truck Utility with Front Mounted Flail Mower and Spreader Loose Material (Salter Unit)

Archived on October 17, 2015. Original response deadline: . Full description on SAM.gov.

Overview

Response deadline
7:00 AM UTC+02:00
Posted
September 14, 2015
Notice type
Solicitation
NAICS
423110: Automobile and Other Motor Vehicle Merchant Wholesalers
Agency
Department of WarDepartment of the Army

Notice details

Office
0409 AQ HQ CONTRACT
Place of performance
W6E1 USAG Stuttgart DOL Prop BK Central Rec Point, Unit 30401 APO AE 09107 EU
PSC
23: MOTOR VEHICLES, CYCLES, TRAILERS
Last updated
Dec 5, 2025

Identifiers

Solicitation number
W564KV15T0094
Notice ID
056919cf542efd8930b3476c7510da9c

Description

Under the authority of FAR Part 12-Acquistion of Commercial Items, and FAR Part 13-Simplified Acquisition Procedures, the 409th Contracting Support Brigade/Theatre Contracting Command (409th CSB/TCC) intends to issue a solicitation for the acquisition of a Utility truck with Front Mounted Flail Mower and Spreader Loose Material (Salter Unit) for USAG Stuttgart, Germany. Statement of NEED/Specifications for a Truck Utility with Front Mounted Flail Mower and Spreader Loose Material (Salter Unit) STATEMENT OF NEED/ Specifications Concept: The items and equipment listed below will be delivered as an end item and component to replace existing equipment that is past the end of life-cycle. This equipment is mission essential as it is required to support the Roads and Grounds Section of the Directorate of Public Works. The new items and equipment will be delivered key ready in order to support the required mission. The contractor will provide all manuals, components and specified support components for the equipment. One important condition requirement is that the vehicle and its components are compatible with current existing mission equipment, (Leave Suction Trailer, Snow Plough and Water Tank). Project Conditions & Timeline Delivery and training will take place in accordance with the agreed upon delivery date coordinated between the Government and the successful offeror. The vehicle will be delivered and per demonstration, turn-key ready with all support equipment and components. Technical Requirements: Utility Truck chassis: 4-wheel drive Vehicle equipment: Chassis version Vario Pilot (dual mode- left/right hand steering) GVW btw. 6.5t and 13t when all attachments are mounted. ldentific. of registration as agricultural tractor Registration as implement carrier (LoF) Standard Windshield size approx. 75 quote mark (190cm) X 43 quote mark (100cm) is extremely required by safety standards (Accident avoidance) so the snow plough or Mower is in sight for the operator Engine 6-cylinder-diesel-engine, 21OKW(286HP) MS5 BlueTec 5 Engine elect. syst.PLD (pump linel nozzle), dir.inj. Standard Exhaust turbo charger and air cooled Standard Exhaust brake, combined, exh. cut-out/cyl. head valve Standard Governor char. switchable, driving implem. opera Standard Hand throttle, electronic Standard Gear box with 8 gears forward switchable to Hydrostatic driving 6 Reverse gears which is extremely needed during snow clearing Exterior noise dampening (7011571EU inci.961201EU) Standard Air pressure,310 1/min-18 bar, maintenance free, wat Standard Intake air pre-heating for starting from cold Standard Air intake pipe, with air filter and pre-separator Standard Protection grid behind both radiators Live engine PTO to rear with flange Live PTO incl. PTO front PTO rpm limiter Fan drive, hydrostatic(needed for special slow driving which is needed for mowing),water-cooled Standard Axles Front axle as portal axle Standard (7 to.) Front axle high capability for front mower with arm attachment Distance between front axle and connecting snow plough/mower attachment is only 900mm (better clearance - extremely when entering streets at inner sections) Permanent 4WD with lockable interaxle differential Standard Differential lock at front axle Rear axle as portal axle Standard (for higher clearance of the ground) Differential lock at rear axle, engageable Standard Frame Continuous, rigid ladder-type frame Standard Integral support for fitting front mounting plate Standard Frame-integrated standardized mounting points Standard Implement mounting plate DIN76060 type B, cat. 3 Rear mounting brackets Aluminium fuel tank, effective capacity 190 liters Standard Vertical exhaust pipe Front towing jaw with pin Standard Trailer coupling, jaw big, Ringfeder, bolt 38,5 Rear cross member reinforced (13 t) Underbody coating (Dinol) Standard Front Mounted Flail Mower: Standard unit for one- and/or two-man operation, designed for front mounting plate size 3 or 5 with the following features: Operation on right- and left-hand side, Reach up to 6 m from centre of vehicle flail arm radius 240 Hydraulic collision protection with absorption of the boom system via hydraulic reservoir Hydraulic lateral shift of flail arm of 1800 mm Electrical switching on/off of float setting of attachments Quick-change device for attachments Implement drive via front PTO-shaft, axial piston hydraulic system, oil tank with mineral oil, capacity 60 liters Safety cut-off System : Electric switch on/off of cutter shaft on control panel, incl. brake valve (stops in approx. 4 seconds) Service hour meter Mechanical torsion frame to prevent vehicle Distortion Transport position of flail arm including attachment in front of the vehicle 2 support legs, height adjustable Spreader Loose Material (Salter Unit) Hopper Auger conveyer system ( quote mark S quote mark ) Salt screen 40x40 mm, steel (for S 17- 30) Cover (for 8/S17- 30, F/012- 35) Standard paint finish RAL 2011 Auger cover (standard) Pre-wet system Pre-wet system 880 Liters (for 17 - 20) Pre-wet coupling Storz 2 quote mark Maximum level switch, 4-pole Drive system Drive system via vehicle hydraulics ( quote mark V quote mark ) Connections at the front of the machine (for V) Hydr. couplings U20 U300-U500 from 1st July 09, IS016028 P=Sz19(F) R=Sz19(M) Control system quote mark CX quote mark control system Cable extension (cabin wall connector). Standard version Control box support, universal (for CB, CX, CL) The Government anticipates awarding a single, firm-fixed-priced contract award through full and open competition. All responsible sources may submit a quotation in response to the solicitation when it is released. To be considered for contract award, all offerors must be registered in the System for Award Management (SAM) at www.sam.gov. The Request for Quotes (RFQ) will be issued via the Army Single Face to Industry (ASFI) website, https://acquisition.army.mil/asfi/default.cfm to Federal Business Opportunities (FedBizOpps) website at http://www.fbo.gov. The solicitation number is W564KV-15-T-0094; hard copies of the solicitation will not be issued. It is the contractor's responsibility to monitor the Government-Wide Point of Entry (GPE) for the solicitation release and all subsequent amendments. The anticipatory issue date for the solicitation is fifteen (15) days from the posting of the pre-solicitation. The delivery will be FOB destination to Stuttgart, Germany. Point of contact for this action is Thomas A. Finan, email thomas.a.finan.civ@mail.mil.

Full description on SAM.gov

Award Overview

No prior contract identified

No prior award matched this notice's agency, NAICS, place of performance and PSC within 18 months. It may be a new requirement.

Contacts

Contracting Officer

Primary Contact

Thomas A. Finan, 06314115516 TCC-Kaiserslautern (PARC Europe, 409th CSB)

Documents

No documents available.

Lifecycle

Solicitation:W564KV15T0094
  1. Market Research
  2. Pre-Solicitation
  3. Solicitation

Award typically follows within 30–90 days after the response deadline. (estimate)

  1. Pre-SolicitationJul 21, 2015

    23--Truck Utility with Front Mounted Flail Mower and Spreader Loose Material (Salter Unit)

    Notice 0227245559bfc29207465c80c51b073e on SAM.gov

  2. Market ResearchJul 28, 2015

    23--Utility Truck - Request For Information.

    Notice c468897a46fb9cefb3044231e2d1417e on SAM.gov

  3. 3×
    Pre-SolicitationAug 20, 2015

    23--Truck Utility with Front Mounted Flail Mower and Spreader Loose Material (Salter Unit)

    Notice 8ebdecbe7b55fdffcdb5880ad82498b5 on SAM.gov

  4. SolicitationCurrentSep 14, 2015

    23--Truck Utility with Front Mounted Flail Mower and Spreader Loose Material (Salter Unit)

    Notice 056919cf542efd8930b3476c7510da9c on SAM.gov

Similar Opportunities

Title
Match
Phase
Deadline

Additional Details

Solicitation Number

W564KV15T0094

Archive Date

Oct 17, 2015