GovChime
Notice ID: 142886f766f743e58bbff4c2d4defeaeSolicitation

Handi Flat Work Barge

Archived on September 21, 2024. Original response deadline: . Full description on SAM.gov.

Overview

Response deadline
2:00 PM UTC−05:00
Posted
August 26, 2024
Notice type
Solicitation
Set-aside
Small Business Set Aside - Total
NAICS
336612: Boat Building
Agency
Department of WarDepartment of the Army

Notice details

Office
W07V ENDIST ST PAUL
Place of performance
Fountain City, 54629
Last updated
Sep 25, 2026

Identifiers

Solicitation number
W912ES24Q0119
Notice ID
142886f766f743e58bbff4c2d4defeae

Description

1. GENERAL DESCRIPTION The Operations Section of the US Army Corps of Engineers, St Paul District is solicitating a Handi-Flat Work Barge for use on the Mississippi River Locks and Dams. Quantity is for one (1) unit, with an option for one (1) or two (2) additional units that will be awarded at the same time if we decide to exercise. The unit cost must include delivery and unloading at the Fountain City Service Base in Fountain City, WI. 2. SPECIFICATIONS: A. Beam 12’ wide. B. Length 40’ long. C. Overall hull molded depth of 4’. D. Rakes on both ends of the barge. E. Rake chines shall not be a welded seam. F. All structural steel construction made from standard Grade A-36 or higher. NO ALUMINUM. G. Hull thickness no less than ¼” thick. H. Head log thickness including the radiused corners on the bow and stern not less than 3/8” thick. I. Minimum of three (3) bulkhead sections allowing four (4) watertight compartments. K. Minimum of two (2) flush mounted 18” diameter deck hatches per compartment mounted in opposite corners. ABS Certified waterproof Hatch covers. L. Minimum allowable deck loading of 750 lbs./sq ft (PSF). M. All barge surfaces shall be sand-blasted free for rust and mill scale. O. All paint shall be two-part epoxy rated for marine application. P. Exterior coating shall be primed and painted of the hull, sides and deck. Q. Barge hull and side coating shall be standard black coating at least 8 mils thick. R. Barge deck shall be standard red non-slip coating. S. Barge interior compartment coating shall be standard white coating. T. Shall come complete with six (6) industry standard 24” kevels with three (3) centered on each side. U. Each of the two long sides and front should have rubber rub rails that can be replaced and that fit in a steel track. Minimum of 6” high and 3” wide extending along the full length. V. Barge must have stake pockets (w/ drain) for removable handrailing that is included. W. Removable handrailing must have a vertical height of between 39” to 45” and support a load of at least 200 lbs. applied within 2” of the top edge. X. Must include a steering counsel complete with steering wheel, steering control and shift/throttle cables to the transom. Y. Includes recessed cable tray area between counsel and transom for control cables and gas lines. Z. Includes portable davit arm with the following specifications: Certified by the manufacturer. 2,000 lb. lift capacity. 12-volt electric winch. Up to 10’ tall. Up to 7’ hook reach. Three permanent bases (stern, starboard, bow). AA. Must include two (2) fully rigged 75 hp four-stroke motors with long shafts, low torque lower units, complete with stainless steel propellors sized for the application. Not counter rotating. AB. Rigging to include standard gauges such as tachometer, water pressure, fuel, battery power. AC. Must include two five-gallon portable gas tanks, and three (3) 12-volt AGM maintenance-free batteries with selector switch between all three batteries. AD. Includes supplied wiring and connections between the battery selector switch to the motors and three davit arm locations. Includes one (1) on-board three-bank battery charger located in the consol. AE. Laser or water-jet cut steel USACE logo and US ARMY CORPS OF ENGINEERS approved font painted and welded to each side, centered above the waterline. Minimum 6” tall font painted white and logo painted red. AF. Serial number 009 laser or water jet cut and welded to rear side above waterline. Minimum 6” tall font painted white. If we exercise the optional barges they shall be numbered 010 and 011 respectively. AG. Digital or hardcopy versions of the shop/concept drawings shall be submitted prior to fabrication for approval. AH. As-built drawings shall also be sent to the government as .dwg file and hard D-size drawings.

Full description on SAM.gov

Award Overview

No prior contract identified

No prior award matched this notice's agency, NAICS, place of performance and PSC within 18 months. It may be a new requirement.

Contacts

Contracting Officer

Secondary Contact

Documents

No documents available.

Lifecycle

Solicitation:W912ES24Q0119
  1. Solicitation

Award typically follows within 30–90 days after the response deadline. (estimate)

  1. SolicitationCurrentAug 26, 2024

    Handi Flat Work Barge

    Notice 142886f766f743e58bbff4c2d4defeae on SAM.gov

Similar Opportunities

Title
Match
Phase
Deadline

Additional Details

Solicitation Number

W912ES24Q0119

Archive Date

Sep 21, 2024

Office Address

SAINT PAUL, MN, 55101-1323