Notice ID: affb1e47c9b04b7db44137d9d63b28a6Award NoticeAwarded
J036 - Calibration on Lucker 200K Test Bed
Awarded on September 23, 2021. Full description on SAM.gov.
Awarded tounder N6883621P0331 (source: SAM.gov award notice)• $3.4K
Overview
- Posted
- October 5, 2021
- Notice type
- Award Notice
- NAICS
- 541380: Testing Laboratories and Services
- Agency
- Department of War
Notice details
- Last updated
- Sep 9, 2025
- Award date
- Sep 23, 2021
- Award amount (SAM.gov award notice)
- $3.4K
Identifiers
- Solicitation number
- N6883621Q0371
- Notice ID
- affb1e47c9b04b7db44137d9d63b28a6
- Award number (PIID)
- N6883621P0331
Description
The Naval Supply (NAVSUP) Systems Command, Fleet Logistics Center Jacksonville ( FLCJ), FL intends to issue a sole source award utilizing Simplified Acquisition Procedures to Roberts Calibration Inc., to provide support services for the annual recertification to calibrate the Lucker 200K (serial #10145) Test Bed equipment located at Trident Refit Facility, Kings Bay, (TRKB) GA. Trident Refit Facility, Kings Bay, GA., Shop 72D needs to certify all lifting and handling gear for support of repair and overhaul of Naval Nuclear Submarines. The 200K Lucker Test Bed requires calibration for its annual recertification that is due to expire in September 2021. Without the monthly recertification of the lifting and handling gear, there would be no support of refit and repair of Naval assets assigned to TRFKB. The original equipment manufacturer was AJT Equipment. AJT Equipments assets, including proprietary software utilized by their equipment, was purchased by Proofcert, LLC, an affiliate of Roberts Calibration Inc. As Roberts Calibration Inc., has access to the proprietary software and expertise and experience in calibrating this equipment in the past, they are considered to be the only responsible source available to calibrate the Lucker 200K Test Bed. The applicable North American Industrial Classification System Code (NAICS) code these services fall under is 541380 Testing Laboratories with a size standard of $16.5M. This notice of intent is for information purposes only. All sources that believe they are eligible to provide this requirement must respond in writing. Responses must be supported with clear and convincing evidence to clearly articulate the ability and technical representation to provide this requirement as outlined above. A request for documentation will not be considered as an affirmative response. If no responses are received within ten (10) calendar days after publication of this notice, to the effect that technical acceptable items are available and that it is more advantageous to the Government than obtaining this product through a sole-source contract, then a sole source acquisition award will be made. Response to this notice is to be sent to deaundrae.l.rogers.civ@us.navy.mil.
Award Overview
Award Number
N6883621P0331
Award Amount (SAM.gov award notice)
$3.4K
Award Date
Sep 23, 2021
Awardee
Awardee UEI
FJA4YAJJFMK6
Original Solicitation
Notice ID: affb1e47c9b04b7db44137d9d63b28a6
Posted Date: Oct 5, 2021
Original Response Deadline: Not specified
More From This Vendor
Top 5 most recent
- $16.2KSigned May 13, 2026
- $18.4KSigned Dec 23, 2025
- $13.6KSigned Jun 6, 2025
- $7.9KSigned May 19, 2025
- $13.6KSigned Dec 23, 2024
Contacts
Documents
No documents available.
Lifecycle
Solicitation:
N6883621Q0371- Awarded
This opportunity has been awarded.
- Special NoticeSep 9, 2021
Trident Refit Facility, Kings Bay, GA., Shop 72D needs calibration services to certify the Lucker 200K Test Bed for support of repair and overhaul of Naval Nuclear Submarines.
- Sole Source / J&AOct 5, 2021
J036 - Calibration on Lucker 200K Test Bed
- AwardedCurrentOct 5, 2021
J036 - Calibration on Lucker 200K Test Bed
Similar Opportunities
Title | Match | Phase | Deadline |
|---|---|---|---|
********************************************************************** UPDATE 10/26/2026 Item 1: Posted Questions and Answers ********************************************************************** Pearl Harbor Naval Shipyard & Intermediate Maintenance Facility (PHNSY & IMF) is a US Navy regional industrial center that maintains, overhauls and repairs various vessels of the US Navy. Its industrial operations provide the US naval forces with a wide range of services and resources located on the island of Oahu, Hawaii, with direct and indirect support to submarines, surface vessels and shore based activities in the Pacific. PHNSY & IMF seeks services to calibrate, provide preventative maintenance and as-needed remedial repairs of three (3) Government-owned Roberts Testing Proof Test Machines to ensure their accuracy, reliability, and safe operation. The Contractor shall provide all necessary labor, materials, and expertise to perform comprehensive calibration, preventative maintenance and as-needed remedial repair services on the Government-owned equipment specified in the Performance Work Statement (PWS) The tentative period of performance for this service: Base Period*: From 16 November 2026 to 15 November 2027 Option Periods*: Option Period 1: 16 November 2027 to 15 November 2028 Option Period 2: 16 November 2028 to 15 November 2029 Option Period 3: 16 November 2029 to 15 November 2030 Option Period 4: 16 November 2030 to 15 November 2031 6 month Option Period: 16 November 2031 to 15 May 2032 *(Performance period may be updated.) The applicable North American Industry Classification System (NAICS) code assigned to this procurement is 541380, Testing Laboratories and Services; Size Standard $19,000,000.00. Product Service Code is L049, Technical representative services- maintenance and repair shop equipment. Please note the following: The solicitation number for this requirement is N32253-27-Q-0001 Quotes are due no later than 11/02/2026 at 11:00 a.m. HST. Quotes must be sent via email to both the primary and secondary points of contact. All firms or individuals responding must be registered with the System for Award Management(SAM) (https://www.sam.gov) by the award date. As part of the price quote package, the Offeror shall submit the completed SF 1449 with blocks 17a., 30a., 30b. and 30c. (SF 1449 page 1) and CLIN information (SF 1449 page’s 3-5) completed. Submission of a signed offer to the Government constitutes agreement and acceptance of the solicited terms and conditions. The Government may revise the solicitation at any time by means of an Amendment. It is an offeror’s responsibility to ensure it is accessing the Government Point of Entry (GPE) website, https://sam.gov/, to view potential amendments and procurement notifications for this solicitation. The proposal shall include: Technical Capability - Please submit a detailed technical quote (not to exceed 10 pages) that clearly demonstrates thorough knowledge and understanding of, and approach to completing the work in accordance with the PWS. The technical quote must contain sufficient details so that it may be evaluated in accordance with the PWS and comply with the period of performance set forth in the solicitation. Nonconformance will deem an Offeror ineligible. The technical quote must consist of a clear plan demonstrating how the offeror will Perform Calibration, Preventative Maintenance and as-needed Remedial Repair Services as required in the PWS. Certifications - Offerors must provide proof it meets the requirements set forth in NAVSEAINST 4734.1B, "Commercial calibration activities, including Original Equipment Manufacturers (OEM), that calibrate NAVSEA TMDE will be certified or accredited by an accrediting body approved NAVSEA 04 to be in compliance with references (p), (r) and/or (s), and the scope of accreditation must cover the appropriate measurement parameters and ranges of the calibrations performed." The Contractor must, for the entire period of performance, maintain a certification or accreditation in compliance with NAVSEAINST 4734.1B. The Contractor's accreditation body must be approved by NAVSEA 04, and the scope of accreditation must encompass all measurement parameters and ranges for the NAVSEA Test, Measurement, and Diagnostic Equipment (TMDE) calibrated under this contract. The Contractor shall make proof of current certification available for Government inspection upon request. Itemized Price Breakdown - Provide an itemized price breakdown of the quote that clearly and concisely describes and defines the Offeror's response to the requirements contained in the solicitation. Cybersecurity Maturity Model Certification (CMMC): DFARS clause 252.204-7021 and DFARS provision 252.204-7025 related to Cybersecurity Maturity Model Certification (CMMC) requirements are included in the solicitation involving Federal Contract Information (FCI) or Controlled Unclassified Information (CUI), on unclassified information systems, effective November 10, 2025. Offerors must possess a valid CMMC Level 1 (Self Assessment) certification at the time of award and for the duration of any resulting contract. The Government will verify the Offeror's CMMC Level 1 (Self-Assessment) certification at the time of award. Offerors failing to meet the requirements in DFARS clause 252.204-7021 and DFARS provision 252.204-7025 will be deemed ineligible for award. The Offeror shall provide, in the proposal, the CMMC unique identifier(s) (CMMC UIDs) issued by SPRS for each contractor information system that will process, store, or transmit FCI or CUI during performance of a contract, task order, or delivery order resulting from this solicitation. Offers must be received no later than the exact closing date and time specified in Block 8 of the SF 1449 (or as updated via subsequent amendments). Offerors are hereby advised that the size limit including attachments is 35 MB per email. Emails that exceed this size limit will not be received by the Government. It is the Offeror's sole responsibility to ensure their Offer is received by the Government POCs no later than the specified closing date and time. When necessary to comply with this size limit, the Offeror may deliver their Offer through multiple emails, with each email clearly marked in the Subject Line indicating its sequence order within the total number of emails being transmitted (for example, email 1 of 3). Offers received after the due date may not be considered unless the Contracting Officer determines that the delay was caused solely by the Government and accepting the Offer is in the best interest of the Government. Contract award will be in accordance to 52.212-2 as stated in the solicitation. All questions regarding solicitation N32253-25-Q-0001 shall be submitted in writing via email to the listed POCs. Questions are due 10/23/2026 03:00 PM HST. | 58% | Solicitation | 11/02/2026 |
Solicitation is attached. | 57% | Combined Synopsis | 10/30/2026 |
Solicitation is attached. | 57% | Combined Synopsis | 10/30/2026 |
Q&A's: 1. CLINs 0001 through 0005 (pages 3-5) are each one firm-fixed-price lot for "Inspection and calibration." SOW paragraphs 1 and 4.2 (pages 1-2) call for lapping only of plates that are out of specification, the QASP (Attachment 0002, page 1) says lapping repairs must be authorized by the CO or COR, and Section G, paragraph 6.a (page 12) asks for labor rates. Should each year's lot price cover inspection and calibration of all 18 plates, with lapping priced separately (for example, a per-plate price or an hourly labor rate) and billed only when authorized? Or should the lot price include all lapping that may be needed that year? If lapping is priced separately, where in the quote should those prices or rates be shown? Answer: Firm fixed for calibration of all plates listed in the SOW. Lapping to be priced separately. We don’t know which plates will require lapping or how much lapping per plate will be needed. We are asking for an hourly rate for lapping. Whether the plate is big or small, the hourly rate would be the same. Plates may require a lot of lapping or very little. Pricing lapping by the plate doesn’t seem to make much sense. 2. Each CLIN (pages 3-5) states "All travel shall be in accordance with the Joint Travel Regulation (JTR)," and SOW paragraph 2 (page 1) says invoices will be checked against the contract prices and JTR approved prices. Should travel be included in each year's firm-fixed lot price, or will it be reimbursed separately at JTR rates? If it is reimbursed separately, how should travel be shown in the quote? Answer: Include estimated travel costs in the firm-fixed pricing. The Vendor that gets the award will bill actual costs after the service. 3. Section G, paragraph 6.c (page 12) asks offerors to "concur at the bottom of the Scope of Work (SOW) and sign," but Attachment 0001 ends at paragraph 15.1 on page 4 with no concurrence or signature block. Is it acceptable to add a signed and dated concurrence statement at the bottom of SOW page 4, or to submit a separate signed concurrence page on company letterhead that references Attachment 0001 dated 15 Oct 26? Answer: Either is fine by me. _______________________ All Vendors MUST submit all requirements plus the signed Soliciation to the POC before the closing date and time or they will not be considered for this action. | 55% | Combined Synopsis | 11/09/2026 |
The Veterans Health Administration, Network Contracting Office 02 intends to solicit from a single source IAW FAR 13.106(b) to obtain a contract for: Calibration Services to Include Maintenance and Repair Services for the Albany VA s currently owned radiation dosimetry calibrators. This equipment is utilized by the Nuclear Medicine department and is used in oncology procedures. Daily QA 3 software provides a graphical presentation of radiation oncology beam measurement data. This technology measures the output, flatness, symmetry, field size, and energy of rotational and Flattening Filter-Free (FFF) beams. This technology allows users to choose which data parameters to view and over what period to view them. A single measurement instance may be examined by clicking on a data point which corresponds to a particular day. This is completed prior to the treatment of patients and requires regular and recurring calibrations to ensure proper operation and safety to the patients receiving treatment. It is currently actively in use at the VA Medical Center (Albany) located at: 113 Holland Ave, Albany, NY 12208. Period of Performance (POP) (estimated): 10/1/2026 through 09/30/2027 with provision of (4) option years. All work to be completed NLT 30 days of receiving an awarded contract. Requirement Description: Sun Nuclear is the Original Equipment Manufacturer (OEM) of the equipment and systems currently in use at the Albany VA Medical Center. These proprietary systems are designed and manufactured exclusively for oncology applications within healthcare facilities. The equipment is regulated medical equipment and that must remain fully operational to support direct patient care activities. This includes Service and maintenance and calibrations of the equipment. These systems are essential for patient safety and effectiveness of therapy. Given the critical nature of this equipment, routine preventative maintenance, inspection, calibration, and repairs are required to prevent downtime and ensure continuous, safe operation. Sun Nuclear manufactures, distributes, and services its Equipment in compliance with applicable regulatory and quality standards. Market research and direct communication with the OEM confirm that Sun Nuclear does not authorize or utilize third-party service providers to perform maintenance or repair work on its proprietary equipment and systems due to maintaining warranty coverage of the equipment. The equipment in question is manufactured, sold, and serviced exclusively by Sun Nuclear Med. The use of non-factory-trained or unauthorized service providers would void the manufacturer s warranty and may compromise equipment integrity, regulatory compliance, and patient safety. Sun Nuclear employs factory-trained and certified service technicians who are specifically trained on their proprietary systems. These technicians possess exclusive access to OEM parts, technical documentation, software updates, calibration tools, and engineering support necessary to properly maintain and repair the equipment. Only these authorized representatives are qualified to perform required maintenance while preserving the binding manufacturer warranty. Given: The proprietary nature of the equipment The OEM s exclusive servicing structure The requirement to preserve manufacturer warranties The regulatory compliance obligations The critical role of the equipment to patient care and safety The Contracting Officer (CO) has determined that no other vendor can meet the agency s needs without unacceptable risk. Therefore, the most suitable and responsible course of action is to sole source this requirement to Sun Nuclear, the OEM and manufacturer, to ensure continued warranty protection, regulatory compliance, operational reliability, and the highest standard of patient health and safety. Place of Performance: Department of Veterans Affairs Albany VAMC 113 Holand Ave. Albany, NY 12208 The NAICS code for this requirement is: 541380 Testing Laboratories and Services (Size Standard: $19.0 Million). Intended Source: Sun Nuclear THIS NOTICE OF INTENT IS NOT A REQUEST FOR COMPETITIVE QUOTES. However, interested parties may identify their interest and capability to respond to this requirement by : Wednesday September 30th 2026 at 17:00 Eastern Standard Time (EST). The Department of Veterans Affairs will NOT be responsible for any costs incurred by interested parties in responding to this notice of intent. Only written responses from responsible sources will be considered. Any prospective contractor must be registered in the System for Award Management (SAM) to be eligible for award. Interested parties are encouraged to furnish information by email only with RESPONSE TO INTENT TO SOLE SOURCE RADIATION DOSIMETRY CALIBRATORS in the subject line. All documents submitted will not be returned. All interested parties shall submit clear and convincing documentation demonstrating their capabilities to satisfy the requirements listed above to Contract Specialist, Jason M. Rundle at jason.rundle@va.gov. The capability documentation should include general information and technical background describing in detail the prospective contractor's capabilities and experience that will demonstrate the ability to support these requirements. Page 1 of Page 2 of 2 Page 1 of | 53% | Special Notice | 09/30/2026 |
Additional Details
Solicitation Number
N6883621Q0371
Archive Date
Apr 5, 2022
Office Address
JACKSONVILLE, FL, 32212-0097